Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
9.1. Specifications.
9.2. The general data
9.3. System of compulsory ventilation картера (PCVсистема)
9.4. System рециркуляции (EGR system)
9.5. System доокисления exhaust gases
9.6. System of catching of steams of gasoline (EEC system)
9.7. System of electronic injection of fuel a self-diagnostics mode
9.8. A regulator of a stream of air
9.9. A regulator of pressure of fuel both the solenoidal valve check and replacement
9.10. Gauges of the processor block
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system


9.4. System рециркуляции (EGR system)

1. It is intended for decrease in the maintenance of oxides of nitrogen in the fulfilled gases at the expense of decrease in temperature of combustion of a gas mixture. It is reached by a redirection of a part of these gases through the valve рециркуляции in soaking up collector. The valve design depends on type of transmission and expected service conditions of the car in the given region. Refusal of this system influences engine work, causing unstable work idling and on small speeds of movement, "failures" at dispersals. The system consists of the valve рециркуляции and valves operating it (or pneumodistributors). On a part of cars valve work рециркуляции the differential valve (ВРТклапан) operates.
2. The system is established on 4цилиндровых engines of cars of 198788 of century and on engines V6 since 1987 system Work the processor block ECU which is a part of processor system ECCS of the car operates. The valve рециркуляции is opened at engine start-up, on the cold engine, on turns above 3200

1.5б the Scheme of distributing of vacuum highways of system of clearing of exhaust gases

3.3 Valve рециркуляции on engines VS is mounted behind the case throttle заслонки on a soaking up collector of rpm or below 900 rpm. In other conditions the valve is closed.

Valve check рециркуляции
3. Find the valve (photo).
4. Check up freedom of moving of a diaphragm, having submitted it upwards (photo). At jamming of a diaphragm the valve replace.
5. Start the engine and close the valve by hand, having pressed on a diaphragm (dress gloves). The engine should lose turns and even to decay. If engine turns do not vary, check up a condition of a tube of selection of exhaust gases. If the return valve exclude it is provided, having connected a hose демпферный the valve and the valve рециркуляции. Warm up the engine and finish turns to 20002500 about / minute Disconnect from the valve рециркуляции a vacuum hose, the diaphragm should be displaced slowly downwards in process of increase of turns. Attach a hose, in process of decrease in turns the diaphragm should be displaced slowly downwards.
6. If the diaphragm does not move, check up depression on the valve. For this purpose disconnect a vacuum hose on which depression should be felt. If depression is present, replace the valve рециркуляции. Otherwise check up a hose condition, serviceability демпферного the valve.
Check of the control differential pneumovalve (ВРТ the valve)
7. Disconnect vacuum hoses in the top part of the valve.
8. Remove the valve. Muffle one of unions and try to create depression through other union if depression manages to be created the valve it is faulty (air should pass freely in a direction отсоса). Create pressure upon the union in the bottom part of the valve, thus air through the vacuum union should not to pass. Otherwise the valve replace. Before valve installation blow hoses.

3.4 Check of a diaphragm of the valve рециркуляции

Check of the vacuum distributive valve (ТVV the valve)
Attention! On 4цилиндровых инжекторных engines the distributive valve is mounted
In a forward part of a soaking up collector.
9. On the cold engine disconnect a vacuum hose on the valve рециркуляции, start the engine and check up depression increase. If depression accrues immediately TW the valve replace. If on the heated-up engine depression is absent, check up a condition of hoses. If hoses are serviceable, TW the valve replace.
Check демпферного the valve
10. Remove the valve and blow from outside connections with the valve рециркуляции, air should pass freely. Air should pass in an opposite direction hardly. Otherwise the valve replace.
Check отсечного the solenoidal valve рециркуляции
11. It is carried out in car-care centre service as the special believed equipment is required.
The control differential pneumovalve (ВРТклапан)
12. Disconnect hoses, turn away screws and raise the valve.
13. Disconnect a tube in the bottom part of the valve and remove the valve.
14. Installation is carried out upside-down.
The vacuum distributor (TW)
15. Merge about 1 l of a cooling liquid.
16. Designate and disconnect vacuum hoses.
17. Turn out the distributor.
18. Installation is carried out upside-down. Wrap the distributor on hermetic.

4.1а Electromagnetic отсечной the valve regulating depression in system доокисления

«The previous page
9.3. System of compulsory ventilation картера (PCVсистема)
The following page»
9.5. System доокисления exhaust gases