> Gauges of the processor block. Nissan Terrano II (with 1985 on 1999 of release)
Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
9.1. Specifications.
9.2. The general data
9.3. System of compulsory ventilation картера (PCVсистема)
9.4. System рециркуляции (EGR system)
9.5. System доокисления exhaust gases
9.6. System of catching of steams of gasoline (EEC system)
9.7. System of electronic injection of fuel a self-diagnostics mode
9.8. A regulator of a stream of air
9.9. A regulator of pressure of fuel both the solenoidal valve check and replacement
9.10. Gauges of the processor block
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







9-10-datchiki-processornogo-bloka.html

9.10. Gauges of the processor block

The gauge of temperature of the engine
Check
1. The gauge requires check at the complicated start-up of the engine and in case of detection of a code 13 in a self-diagnostics mode (see above).

9.2 Check of the gauge of temperature of the engine


2. If the engine there are no obvious signs of incomplete combustion of fuel disconnect the plug and repeat start attempt. If the engine is not started, turn out the gauge and check up its resistance depending on temperatures (photo). If resistance differs from norm the gauge replace. Otherwise check up a gauge chain.
3. Establish the gauge upside-down.
Check of the gauge of temperature of exhaust gases
4. The gauge requires check in case of detection of a code 35 in a self-diagnostics mode (see above).
5. If in a mode круизконтроля the engine works unstably disconnect a socket and check up a course of the car (photo).
6. If the car course has improved, the gauge replace. Otherwise include ignition and check up pressure on a conclusion of a socket which should be nearby 5 In (photo).

9.5 Socket of the gauge of temperature of exhaust gases on engines  V6 and К24


9.6 Check of pressure between a conclusion of a socket of the gauge and weight


9.7 Check of a chain of a conclusion of a socket of the gauge on weight


9.10 Socket of the gauge of oxygen on engines V6 and KS4


9.12 Check of pressure on a conclusion of a socket of the gauge of oxygen


9.13 Check of a chain of the gauge of oxygen on weight on engines V6


9.16а the Socket of the gauge of temperature of air on engines K24


7. Switch off ignition and check up a chain on weight (photo).
8. If pressure differs from 5 In or in a chain there is a breakage the gauge replace.
Check of the gauge of oxygen
9. The gauge requires check in case of detection of a code 33 in a self-diagnostics mode (see above).
10. If in a mode круизконтроля the engine works unstably disconnect a socket and check up a course of the car (photo).
11. If the car course has improved, the gauge replace. Otherwise finish turns to 2000 rpm and later 2 mines be convinced that on the processor block the green signal blinks.
12. On engines V6 at the included ignition check up pressure between a conclusion of a socket And and weight which should be nearby 12 In (photo),
13. Switch off ignition and check up a chain on weight (photo).

Attention!
On engines V6 a chain the ohmmeter should show a chain between a conclusion And and weight, and on engine K24 between a conclusion and and a conclusion 19 sockets on the processor block.

14. If pressure differs from 12 In or in a chain there is a breakage the gauge replace.

9.16 pressure Check on a conclusion of a socket of the gauge of temperature of air


Check and replacement of the gauge of temperature of air (on engine K24)
15. The gauge requires check in case of detection of a code 41 in a self-diagnostics mode (see above).
16. Open a socket of the gauge (photo) and at the included
Ignition check up pressure between a socket conclusion In and weight which should be nearby 5 In (photo).
17. If pressure corresponds to norm switch off ignition and check up a chain between a conclusion And and weight.
18. Check up resistance of the gauge which should be at 20 ° About 2,1 2,9 Ohm, and at 80 ° About 270300 Ohm.
19. In need of replacement turn out the gauge from the air filter and screw the new.

«The previous page
9.9. A regulator of pressure of fuel both the solenoidal valve check and replacement
The following page»
10. A mechanical transmission