Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
8.1. Specifications
8.2. Ignition system the general data
8.3. System of ignition check
8.4. The distributor removal
8.5. The distributor installation
8.6. The rotation gauge коленвала check
8.7. The coil of ignition removal and installation
8.8. System of start-up of the engine the general data
8.9. System of start-up of the engine check
8.10. A starter removal and installation
8.11. The traction relay removal and installation
8.12. A starter replacement of brushes
8.13. Charge system the general data
8.14. The generator leaving and safety measures
8.15. System of a charge check
8.16. The generator removal and installation
8.17. A regulator of pressure and a brush replacement
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







8-12-starter-zamena-shhetok.html

8.12. A starter replacement of brushes

Starter without a reducer
1. Remove a starter and the traction relay.
2. Remove a back sealant (photo).

11.2б starter Details (without a reducer) rear-wheel cars with 4цилиндровым the engine 1. The traction relay 2. An anchor 3. A sealant 4. A lock washer 5. A persistent washer 6. A back cover 7. The back plug 8. Щеткодержатель 9. A brush () 10. A brush (+) 11. Ярмо


11.2в starter Details (without a reducer) all-wheel drive cars with 4цилиндровым the engine 1. Adjusting linings (a thickness of 0,5 or 0,8 mm) 2. The traction relay 3. A back cover 4. Ярмо 5. A winding of excitation 6. A brush (+) 7. An anchor 8. Щеткодержатель 9. Рыч


11.6 ShChetkoderzhatel a starter


11.12 Take away springs and get brushes 1. Щеткодержатель 2. A hook 3. A brush


11.9а starter Details (with a reducer) cars with 4цилиндровым the engine 1. The traction relay 2. An adjusting lining (sealant) 3. A spring 4. The lever 5. A forward cover 6. The case of a reducer 7. A lining 8. A leading gear wheel 9,18. A ring 10. An anchor 11. About


11.9б starter Details (with reducers) cars with engine V6 1. The traction relay 2. An orbital gear wheel 3. A back cover 4. A sealant 5. A bolt 6. An anchor 7. Ярмо 8. A partition 9. Washers 10. Щеткодержатель 11. Planetary gear wheels 12. A leading gear wheel 13. Ш


14.4 Fixing of brushes by a wire piece


3. Get a lock ring and a persistent washer.
4. On a back cover turn away two screws щеткодержателя.
5. Turn out coupling bolts and remove a back cover.
6. Get щеткодержатель (photo), take away springs and get brushes. If the height of brushes is less 12 mm отпаяйте them also solder the new.
7. Collect a starter upside-down.
Starter with a reducer
8. Remove a starter and the traction relay.
9. Turn out coupling bolts (photo).
10. Remove a back cover, without having damaged a ring.
11. Separate from a cover ярмо in gathering with an anchor and щеткодержателем.
12. Take away springs and get brushes from щеткодержателя (photo), отпаяйте and solder new (if height of brushes of less norm).
13. Collect a starter upside-down.

«The previous page
8.11. The traction relay removal and installation
The following page»
8.13. Charge system the general data