> Fuel and exhaust systems. Nissan Terrano II (with 1985 on 1999 of release)
Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
7.1. Fuel system - the general data
7.2. The fuel filter - replacement
7.3. Idling turns - check and adjustment
7.4. A fuel highway - repair
7.5. A cable of a drive throttle заслонки - removal and installation
7.6. A pedal - removal and installation
7.7. The fuel pump - check
7.8. The fuel pump - removal and installation
7.9. System of electronic injection of fuel - the general data
7.10. Units of control and measuring system with processor block ECCS - the general data
7.11. Декомпрессия fuel system
7.12. The case throttle заслонки (for systems with preliminary injection ТВI of systems) removal and installation
7.13. An atomizer replacement
7.14. System of injection of fuel – adjustments System of preliminary injection (TBI)
7.15. Fuel system clearing
7.16. A tank removal and installation
7.17. The gauge of level of fuel removal and installation
7.18. A tank washing
7.19. An exhaust system the general data
7.20. A forward exhaust pipe removal and installation
7.21. Katalitichesky нейтрализаторснятие and installation
7.22. The muffler removal and installation
7.23. An average pipe removal and installation
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system


7. Fuel and exhaust systems

Specifications of engines with fuel injections (К24 and У6), the sizes and backlashes are given in mm
Check and adjustment of turns of idling
For engines with preliminary injection (gas mixture preparation)
Backlash G (between the platen of draught and a cam, the text see)
Installation of backlash G at adjustment
Installation of a backlash for engines with direct injection of fuel (К24)
From a manual transmission
With automatic transmission
Adjusting data of the automatic proof-reader of idling
Idling turns (at the switched off conditioner)
Cars from a manual transmission
The 4-cylinder engine
900+50 rpm
800+50 rpm
Cars with automatic transmission
The 4-cylinder engine
650+50 rpm
700±50 rpm
Idling turns at the included conditioner (transmission in position N)
900+50 rpm
Turns at which the pneumoshock-absorber rod adjoins to the lever throttle заслонки
4-tsilindroyj the engine
1600±50 rpm
1300±50 rpm
The fuel pump
Pressure of fuel (in кГс/см2)
For engines with preliminary preparation of a gas mixture
For engines with direct injection of fuel
Engine V6
With additional depression
Without depression
Engine K24
With additional depression
Without depression

The inhaling moments (in Н.м.)
Nuts of the case throttle заслонки
Till 1992
1st stage of an inhaling
2nd stage
Bolts of the electromagnetic valve отсечки fuel
Drain stopper of a fuel tank
Bolts of a back arm of a fuel tank
Bolts of fastening of a fuel tank
Till 1990
Since 1991
Fastening bolts каталитического neutralizer

Till 1990
Since 1991 for car Pathfinder engine V6
Bolts of fastening of a forward exhaust pipe to final kol - to the lecturer
Since 1991 for car Pathfinder engine V6

«The previous page
6.19. The control panel a heater and the conditioner - removal, installation and adjustment
The following page»
7.1. Fuel system - the general data