Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
7.1. Fuel system - the general data
7.2. The fuel filter - replacement
7.3. Idling turns - check and adjustment
7.4. A fuel highway - repair
7.5. A cable of a drive throttle заслонки - removal and installation
7.6. A pedal - removal and installation
7.7. The fuel pump - check
7.8. The fuel pump - removal and installation
7.9. System of electronic injection of fuel - the general data
7.10. Units of control and measuring system with processor block ECCS - the general data
7.11. Декомпрессия fuel system
7.12. The case throttle заслонки (for systems with preliminary injection ТВI of systems) removal and installation
7.13. An atomizer replacement
7.14. System of injection of fuel – adjustments System of preliminary injection (TBI)
7.15. Fuel system clearing
7.16. A tank removal and installation
7.17. The gauge of level of fuel removal and installation
7.18. A tank washing
7.19. An exhaust system the general data
7.20. A forward exhaust pipe removal and installation
7.21. Katalitichesky нейтрализаторснятие and installation
7.22. The muffler removal and installation
7.23. An average pipe removal and installation
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







7-5-tros-privoda-drosselnojj-zaslonki-snyatie-i-ustanovka.html

7.5. A cable of a drive throttle заслонки - removal and installation

1. Remove the air filter.
2. Disconnect a cable from the case заслонки (photo).

4.1 Fuel highway of engines with fuel injection
1. A tube of giving of fuel
2. A return gasoline pipe line
3. A tube of selection of steams of gasoline
4. The control valve
5. The gauge of level of fuel
6. The pump
7. A lining
8. A tank
9. A tank guard (on all-wheel drive and /


3. Submit on itself a cuff and get a cable from a cut in an arm (photo).
4. Turn away bolts of a directing tube and extend a cable through a partition (photo).
5. Installation is carried out upside-down. Grease a cuff консистентной with greasing. Check up cable work, having pressed a pedal, - заслонка should open completely. Adjust a cable rotating a nut of a cover of a cable. On cars with automatic transmission by pressing a pedal the rod of the switch of a hill-climbing gear (kick-down - the switch) should be involved completely.

5.2а to disconnect a cable заслонки or the cruise-control turn away a nut and get a cable cover. Then pull together муфты on loops of cables and get cables.


5.2б the Pedal and a drive throttle заслонки
1. The lever заслонки
2. A tube
3. A nylon cuff
4. A counternut
5. An arm and a spring
6. A pedal
7. The lever
8. A cable
9. A collar


5.3 Detachment of a cable from a pedal


6. On cars about cruise - by the control (an automatic regulator of speed) at first adjust a cable throttle заслонки, then - a regulator cable.

«The previous page
7.4. A fuel highway - repair
The following page»
7.6. A pedal - removal and installation