6-19-panel-upravleniya-otopitelem-i-kondicionerom-snyatie-ustanovka-i-regulirovka.html
6.19. The control panel a heater and the conditioner - removal, installation and adjustment1. Disconnect the battery from weight. Remove a tray for trifles (if it is provided).
2. Disconnect from the fan and from a heater cables. It is recommended to translate the temperature regulator lever in position Cold.
3. Remove with рычажков handles (photo) and remove the control panel.
4. Turn away screws (photo), get the panel and disconnect sockets.
5. If necessary remove and check up the fan switch (Gl. 12). The switch is disconnected from the panel.
|
17.4 Highways are disconnected from the compressor after отворачивания these bolts
|
|
19.3 For removal of handles submit them directly on itself.
|
|
19.3 Remove with рычажков handles and remove the control panel.
|
|
19.4 Will turn away screws, get the panel and disconnect sockets.
|
6. Installation is carried out upside-down. Adjust draughts of management заслонками.
Adjustment
7. For adjustment of draughts делительной заслонки and заслонки a defreezing nozzle at first disconnect a cable of lateral draught and adjust draught делительной заслонки. Attach a cable and adjust.
8. For adjustment of draught of management заслонкой a ventilating air line displace lateral draught in a direction arrows (photo). Keeping the top and bottom levers in the bottom position, attach in the order of draught 1 and 2 to corresponding levers.
9. For adjustment of draught of management заслонкой a defreezing nozzle displace lateral draught in a direction arrows (photo). Having submitted the lever заслонки a defreezing nozzle in an arrow direction, attach a rod to lateral draught.
10. For adjustment of a cable of management воздухопритоком submit a cover of a cable and lateral draught in an arrow direction. Fix a cover a collar in this position.
11. For adjustment of draught of the crane of a heater disconnect from the lever mixing заслонки a cable of a temperature regulator and adjust draught. Attach a cable and adjust. Submit the lever mixing заслонки in a direction arrows (photo). Translate draught of the crane of a heater in an arrow direction that between draught and the lever was about 2 mm and attach bent for to the lever заслонки.
|
19.10 Adjustment of a cable of management воздухопритоком
1. Lateral draught
2. A tax in this direction
3. A collar
4. Extreme position
|
|
19.8 Adjustment of draught of management заслонкой a ventilating air line
1. The lever заслонки the top
2. The lever заслонки the bottom
3. A tax in this direction
4. Lateral draught
5. Заслонки 1 and 2
|
|
19.9 Adjustment of draught of management заслонкой a defreezing nozzle
1. The lever заслонки
2. Lateral draught
3. A tax in this direction
4. A rod
|
|
19.11 Adjustment of draught of the crane of a heater
1. A tax
2. To pull
3. The lever of draught of management of the crane
4. Draught
5. The lever mixing заслонки
|
|
19.12 Adjustment of a cable of a temperature regulator
1. Mixing заслонка
2. A tax
3. Position of the maximum cooling
|
12. For adjustment of a cable of a temperature regulator displace рычажок to the left (photo), submit a cover of a cable and the lever заслонки in a direction of an arrow and fix a cover a collar.
|
19.13 Adjustment of a cable заслонки an air inlet
1. The lever заслонки an air inlet
2. A collar
3. A tax in this direction
4. Position рычажка managements
|
13. For cable adjustment заслонки an air inlet displace рычажок to the full to the left (photo), submit a cover of a cable and the lever заслонки in a direction of an arrow and fix a cover a collar.
|