Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
5.1. The general data
5.2. Compression check in engine cylinders
5.3. Dismantle of the power unit - security measures
5.4. The engine - removal and installation
5.5. Engine major repairs - the general data
5.6. Engine restoration - alternatives
5.7. Engine major repairs - a dismantling order
5.8. A head of the block of cylinders - dismantling.
5.9. A head of the block of cylinders-clearings and condition check
5.10. A head of cylinders - assemblage
5.11. Shatunno-piston group-dismantle
5.12. Коленвал - dismantle
5.13. The block of cylinders - clearing
5.14. The block of cylinders - condition check
5.15. Rods and pistons - condition check
5.16. Kolenval - condition check
5.17. Radical and шатунные bearings - check and selection
5.18. Engine-assembly order major repairs
5.19. Piston rings - installation
5.20. Kolenval - installation and check of backlashes of radical bearings
5.21. A back epiploon - installation
5.22. Rods and pistons - installation and check of backlashes in шатунных bearings
5.23. Start-up of the engine after repair and обкатка
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







5-8-golovka-bloka-cilindrov-razborka.html

5.8. A head of the block of cylinders - dismantling.

1. For dismantling of a head of the block of cylinders it is necessary to remove all valves and details клапанного the mechanism. At the description it is supposed that cam-shafts and platens with коромыслами are already removed (the Part) See.
2. All valves with details should be sorted separately that at assemblage to establish on former places (photo).
3. Compress a spring of the first valve by means of the adaptation and remove crackers (photo).Осторожно release a valve spring, remove springs, a plate and a basic washer, remove from plugs caps.
4. Remove other valves.

8.2 Store each removed valve and details in a separate package


8.3 Compression of a spring


7.1а Hinged units of the 4-cylinder engine 1. A final collector 2. The pump of a cooling liquid 3. The fan 4. A belt 5. An adjusting arm of the generator 6. The generator 7. A ventilation zolotnik картера 8. The gauge of pressure of oil 9. A tube of ventilation 1


7.16 Details of the 4-cylinder engine
1. A cover of a head of cylinders
2. Platens with коромыслами
3. Springs and valves    
4. The final valve
5. A cracker
6. A plate
7. A cap
8. A spring washer
9. A ring
10. The plug  
11. A saddle
12. A flywheel
13. Гидротр


7.1в Hinged units of engine VS
1. The ignition distributor
2. A final collector
3. A tube рециркуляции
4. A lining
5. A tube эжекции air  
6. A support pillow
7. The pump of a cooling liquid (for rear-wheel а/м)
8. A sealant
9.


7.1 г engine V6 Details
1. An epiploon
2. The holder of an epiploon
3. A lining
4. A flywheel (a leading disk of the hydrotransformer)
5. A back plate (in all-wheel drive а/м it is established on hermetic)
6. A cover
7. The radical bearing
8. The pallet (for заднеприво


7.1д engine K24 Details
1. A washer of a leading disk
2. A leading disk
3,7 Back plate
4. Radical bearings
5. A cover
6. A flywheel (for а/м from a manual transmission)
8. The pallet
9. A stopper
10. A skeleton of covers of radical bearings
11. Коленвал
12. Шатунный


9.6 Check of a demountable plane of a head
1. Calibre                                    
2. Щуп


9.8 Width of a regional corbel of the valve
1. A corbel                                         
2. The corbel is absent


5. After removal of valves and their sorting out carefully clear a head of cylinders and check up its condition.

«The previous page
5.7. Engine major repairs - a dismantling order
The following page»
5.9. A head of the block of cylinders-clearings and condition check