Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
5.1. The general data
5.2. Compression check in engine cylinders
5.3. Dismantle of the power unit - security measures
5.4. The engine - removal and installation
5.5. Engine major repairs - the general data
5.6. Engine restoration - alternatives
5.7. Engine major repairs - a dismantling order
5.8. A head of the block of cylinders - dismantling.
5.9. A head of the block of cylinders-clearings and condition check
5.10. A head of cylinders - assemblage
5.11. Shatunno-piston group-dismantle
5.12. Коленвал - dismantle
5.13. The block of cylinders - clearing
5.14. The block of cylinders - condition check
5.15. Rods and pistons - condition check
5.16. Kolenval - condition check
5.17. Radical and шатунные bearings - check and selection
5.18. Engine-assembly order major repairs
5.19. Piston rings - installation
5.20. Kolenval - installation and check of backlashes of radical bearings
5.21. A back epiploon - installation
5.22. Rods and pistons - installation and check of backlashes in шатунных bearings
5.23. Start-up of the engine after repair and обкатка
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







5-23-pusk-dvigatelya-posle-remonta-i-obkatka.html

5.23. Start-up of the engine after repair and обкатка

1. After the assemblage termination check up level of oil and cooling liquid twice.
2. At the turned out candles both disconnected system of ignition and the fuel pump turn коленвал to wash the cop of registration of pressure of oil with the gauge,
3. Screw candles, dress tips of high-voltage wires and connect system of ignition and the fuel pump.

22.6а Label F on the piston of the 4-cylinder engine


22.6б Kernenie on engine V6 piston


22.8 Introduction of the piston in the cylinder


22.9а the Piece of calibre for backlash measurement in шатунном the bearing


22.9б backlash Definition


4. Start the engine. The engine should be started immediately, after the short time interval necessary for increase of pressure of fuel.
5. Warm up the engine, watching closely occurrence of leaks of oil or a cooling liquid.
6. Stop the engine and check up levels of oil and cooling liquid.
7. Disperse the car from speed of 50 km/hour to 90 km/hour, release a pedal throttle заслонки, having braked the car the engine till the speed of 50 km/hour. Cycle a loop 10-12 times. Thus occurs extra earnings of piston rings to walls of cylinders. Once again check up oil and liquid levels.
8. Make a trip on 800 km, without subjecting the engine to the big loadings (move on low speed), periodically checking oil level. During the period обкатки the raised expense of oil is possible.
9. After run of 900-1100 km replace oil and the oil filter.
10. At run of subsequent several hundreds kilometres conduct the car in a normal mode, avoiding too big and too small loadings.
11. After 3300 km of run again replace oil and the oil filter then the engine is considered the past обкатку.

«The previous page
5.22. Rods and pistons - installation and check of backlashes in шатунных bearings
The following page»
6. Systems of cooling, heating, ventilation and air-conditioning