Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
5.1. The general data
5.2. Compression check in engine cylinders
5.3. Dismantle of the power unit - security measures
5.4. The engine - removal and installation
5.5. Engine major repairs - the general data
5.6. Engine restoration - alternatives
5.7. Engine major repairs - a dismantling order
5.8. A head of the block of cylinders - dismantling.
5.9. A head of the block of cylinders-clearings and condition check
5.10. A head of cylinders - assemblage
5.11. Shatunno-piston group-dismantle
5.12. Коленвал - dismantle
5.13. The block of cylinders - clearing
5.14. The block of cylinders - condition check
5.15. Rods and pistons - condition check
5.16. Kolenval - condition check
5.17. Radical and шатунные bearings - check and selection
5.18. Engine-assembly order major repairs
5.19. Piston rings - installation
5.20. Kolenval - installation and check of backlashes of radical bearings
5.21. A back epiploon - installation
5.22. Rods and pistons - installation and check of backlashes in шатунных bearings
5.23. Start-up of the engine after repair and обкатка
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







5-22-shatuny-i-porshni-ustanovka-i-proverka-zazorov.html

5.22. Rods and pistons - installation and check of backlashes in шатунных bearings

1. Before installation of pistons in gathering with rods the cylinder surface should be absolutely pure, the facet should be removed from edges of cylinders, and the cranked shaft is established in the block of cylinders.
2. Wipe a back surface new top шатунного the loose leaf and lay it in a place in a rod. Be convinced that the ledge on the loose leaf has come into sample in a rod and lubricant apertures have coincided (photo). The loose leaf not to grease. Similarly establish in a rod cover the bottom loose leaf.
3. Place joints of piston rings according to the scheme (photo).
4. Grease pistons and rings with pure oil for the engine, compress rings the adaptation (photo), having left an acting site of the piston.

22.3а Arrangement of joints of piston rings (till 1990)
1. Top компрессионное a ring
2. The top disk маслосъемного rings
3. A dilator маслосъемного rings
4. A rotation plane коленвала
5. A finger axis
6. The bottom disk маслосъемного rings
7. 


22.2 Installation of the loose leaf in a rod


5. Turn коленвал to the bottom dead point in the first cylinder, oil walls of the cylinder for the engine.
6. Сориентируйте the piston so that label F or кернение (on engine V6) (photos) have been turned towards a forward part of the engine.
7. Cautiously enter the bottom part of the piston with a rod into the first cylinder against the stop adaptations for обжатия rings in the block of cylinders. Slightly knock on an upper edge оправки for uniform contact to a plane of the block of cylinders.
8. Enter the piston into the cylinder, cautiously tapping with the wooden handle of a hammer on the bottom of the piston (photo). The big effort not to apply.
9. Draw a rod to a neck коленвала and check up a backlash in шатунном the bearing (photo). Check procedure

22.36 Arrangement of joints of piston rings (after 1990)
1. Top компрессионное a ring
2. The top disk маслосъемного rings  
3. The bottom disk маслосъемного rings
4. Bottom компрессионное a ring
5. To a forward part of the engine
6. A dilator маслосъе


22.4 Preparation of the piston and a rod to installation in the cylinder differs nothing from procedure for radical bearings (see above). Rotation коленвала or the slightest hit of oil on loose leaves at measurements are not supposed. Nuts of a cover of a rod tighten with the set


10. Cautiously remove the calibre rests, grease loose leaves and a neck коленвала, establish a cover and in regular intervals tighten nuts with the set moment.
11. Repeat these operations for other rods.
12. After definitive installation of pistons with rods,
Check up rotation freedom коленвала.
13. Check up axial люфт a rod (see above). Have in view of that after installation of new details люфт and can be less norms and polishing of rods is required.
14. Collect and establish the engine, being guided by corresponding sections

«The previous page
5.21. A back epiploon - installation
The following page»
5.23. Start-up of the engine after repair and обкатка