Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
5.1. The general data
5.2. Compression check in engine cylinders
5.3. Dismantle of the power unit - security measures
5.4. The engine - removal and installation
5.5. Engine major repairs - the general data
5.6. Engine restoration - alternatives
5.7. Engine major repairs - a dismantling order
5.8. A head of the block of cylinders - dismantling.
5.9. A head of the block of cylinders-clearings and condition check
5.10. A head of cylinders - assemblage
5.11. Shatunno-piston group-dismantle
5.12. Коленвал - dismantle
5.13. The block of cylinders - clearing
5.14. The block of cylinders - condition check
5.15. Rods and pistons - condition check
5.16. Kolenval - condition check
5.17. Radical and шатунные bearings - check and selection
5.18. Engine-assembly order major repairs
5.19. Piston rings - installation
5.20. Kolenval - installation and check of backlashes of radical bearings
5.21. A back epiploon - installation
5.22. Rods and pistons - installation and check of backlashes in шатунных bearings
5.23. Start-up of the engine after repair and обкатка
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







5-20-kolenval-montazh-i-proverka-zazorov-korennykh-podshipnikov.html

5.20. Kolenval - installation and check of backlashes of radical bearings

1. Arrange the block so that the bottom part has been turned upwards. On 4-cylinder engines establish an oil separator with a grid (photo).

19.8б Installation маслосъемного a disk


19.10б Installation of piston rings with the help экспандера


2. Turn out bolts of covers, get covers and spread out them as their installation.
Get from covers and the block of cylinders loose leaves of old radical bearings and wipe covers and beds absolutely.
3. Clear an external surface of the new radical loose leaves having oil flutes, and enclose them in bed of the block of cylinders. Corresponding reciprocal loose leaves enclose in covers. Be convinced that the ledge on the loose leaf coincides with sample on the block or on a cover, Besides, the aperture of the oil channel in bed of the block of cylinders should be combined with an aperture in the loose leaf (photo).

Attention!
Are not supposed loose leaf installation on places, hammer blows, and also drawing of scratches at installation.
At the given stage the loose leaf not to grease.


4. On engines V6 the loose leaf with a fillet is established in a back cover and bed of the block of cylinders, on 4-cylinder engines such loose leaf is established in an average cover.

20.1 On 4-cylinder engines before assemblage establish an oil separator with a grid


5. Establish коленвал and measure backlashes in radical loose leaves. For this purpose put on a piece калибровочной a wire on each radical neck коленвала in parallel its axes (photo). Clear surfaces of loose leaves in covers, establish covers and tighten bolts in three steps with the set moment in the specified sequence (photo). Turn away bolts and cautiously lift covers, compare a thickness of each of crushed проволок to a scale on packing and define size of a backlash (photo).
6. If the backlash does not correspond to norm    wrong  selection  of dimensional  group of loose leaves can  be the reason          . Be convinced that at measurements between bearings and surfaces of covers were absent-pollution or oil. If the width of the crushed wire on the ends strongly differs, the radical neck коленвала has конусность.
7. Remove from necks the rests of a wire and remove коленвал.
8. Grease radical necks коленвала and establish in the block of cylinders. Establish covers on former places so that arrows have been turned towards a forward part of the engine. On 4-cylinder engines the back cover is established on hermetic (photo).
20.5б Sequence of a tightening of bolts of covers of radical bearings on 4-cylinder engines


20.3 Loose leaves in the block of cylinders


20.5а Pieces калибровочной a wire for measurement of backlashes in radical bearings


20.5в Sequence of a tightening of bolts of covers on engines V6


20.5г backlash Definition in radical bearings


9. Tighten bolts in three steps with the set moment.
10. Establish directing bearing in коленвал (on а/м from a manual transmission).
11. Check up rotation freedom коленвала.
12. Check up axial люфт коленвала (see above).
13. On 4-cylinder engines establish lateral уплотнители (photo).

20.8 Installation of a back cover on 4-cylinder engines 1. The block of cylinders 2. A back cover 3. Places of drawing of hermetic



«The previous page
5.19. Piston rings - installation
The following page»
5.21. A back epiploon - installation