Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
5.1. The general data
5.2. Compression check in engine cylinders
5.3. Dismantle of the power unit - security measures
5.4. The engine - removal and installation
5.5. Engine major repairs - the general data
5.6. Engine restoration - alternatives
5.7. Engine major repairs - a dismantling order
5.8. A head of the block of cylinders - dismantling.
5.9. A head of the block of cylinders-clearings and condition check
5.10. A head of cylinders - assemblage
5.11. Shatunno-piston group-dismantle
5.12. Коленвал - dismantle
5.13. The block of cylinders - clearing
5.14. The block of cylinders - condition check
5.15. Rods and pistons - condition check
5.16. Kolenval - condition check
5.17. Radical and шатунные bearings - check and selection
5.18. Engine-assembly order major repairs
5.19. Piston rings - installation
5.20. Kolenval - installation and check of backlashes of radical bearings
5.21. A back epiploon - installation
5.22. Rods and pistons - installation and check of backlashes in шатунных bearings
5.23. Start-up of the engine after repair and обкатка
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







5-17-korennye-i-shatunnye-podshipniki-proverka-i-podbor.html

5.17. Radical and шатунные bearings - check and selection

1. Radical and шатунные bearings at  engine major repairs    are subject  to the obligatory  replacement, however the bearings which were in operation should be checked up carefully to restore the general condition of the engine at the moment of repair.
2. Sources of rupture of bearings of a cranked shaft are insufficient greasing because of wrong assemblage (overlapping of channels, a small backlash), pollution and penetration of extraneous particles (untimely replacement of oil and the filter, infringement of consolidations), frequent overloads of the engine and corrosion (it is caused by frequent short trips). Irrespective of the reason which have caused destruction of bearings, it should be eliminated.
3. If коленвал will not be перешлифовываться it is necessary to pick up bearings of standard dimensional group (after repolishing of necks repair bearings) are established only  . After selection it is necessary to check up backlashes in bearings.


17.5а the Diagram of selection of radical loose leaves on 4-cylinder engines

17.5б the group Loose leaf In has marks of dark blue colour
1. Group And                                   
2. Group In
3. Marks


17.5б Places of drawing of numbers of dimensional groups of I radical bearings on engines V6
1. Dimensional group of 1 th bearing
2. To a forward part of the engine

4. On 4-cylinder engines number of dimensional group of radical bearings is beaten out on a plane under-dona (photo).
5. On 4-cylinder engines on 2nd and 4th necks are established group loose leaves In (if коленвал not перешлифовывался). The group of loose leaves of necks 1,3 and 5 (And or) is beaten out on the pallet (photo).

3. A place of drawing of number of dimensional group of a neck коленвала (are put as it should be from 7 th necks to 5th) 4. Places of drawing of numbers of the radical loose leaf



Loose leaf number
Number of dimensional group of a neck коленвала
0
1
2
0
0
1
2
1
1
2
3
2
2
3
4
17.5в the Table of codes for selection of radical loose leaves on engines K24


17.6а the Place of drawing of numbers of groups of support паренных necks on engines V6 (is perfectly in order from right to left), 1st support - in front, 4th - behind.


6. On number engines V6 it is necessary to define in addition dimensional groups of loose leaves and a radical support, and then on the sum of these numbers (or from the table) to define group of the loose leaf (photo).

«The previous page
5.16. Kolenval - condition check
The following page»
5.18. Engine-assembly order major repairs