Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
5.1. The general data
5.2. Compression check in engine cylinders
5.3. Dismantle of the power unit - security measures
5.4. The engine - removal and installation
5.5. Engine major repairs - the general data
5.6. Engine restoration - alternatives
5.7. Engine major repairs - a dismantling order
5.8. A head of the block of cylinders - dismantling.
5.9. A head of the block of cylinders-clearings and condition check
5.10. A head of cylinders - assemblage
5.11. Shatunno-piston group-dismantle
5.12. Коленвал - dismantle
5.13. The block of cylinders - clearing
5.14. The block of cylinders - condition check
5.15. Rods and pistons - condition check
5.16. Kolenval - condition check
5.17. Radical and шатунные bearings - check and selection
5.18. Engine-assembly order major repairs
5.19. Piston rings - installation
5.20. Kolenval - installation and check of backlashes of radical bearings
5.21. A back epiploon - installation
5.22. Rods and pistons - installation and check of backlashes in шатунных bearings
5.23. Start-up of the engine after repair and обкатка
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







5-10-golovka-cilindrov-sborka.html

5.10. A head of cylinders - assemblage

1. Be convinced of cleanliness of a head of cylinders.
2. Establish basic washers of springs.
3. Напрессуйте on directing plugs caps new oil-demountable with the help оправки or adaptations (photo). Rotation of caps at напрессовке is not supposed
4. Oil a core of the valve for the engine and establish the first valve. Establish a plate and crackers and check up spring height in working order (i.e. distance between a basic washer and the bottom surface of a plate in position of the closed valve, a photo). If necessary adjust height installation of additional basic washers.

10.3 Napressovka of caps by means of the adaptation


10.4 Check of height of a spring in working order


5. Remove a plate and crackers and establish both springs dense навивкой downwards (photo).
6. Compress springs and establish crackers. If necessary grease crackers консистентной with greasing temporarily to fix on a core of the valve (photo).
7. Similarly establish other valves. Again check up height of springs (photo) and adjust basic washers. Installation of superfluous basic washers is not supposed if the initial height of a spring in working order corresponds to norm.

10.5 Orientation of springs of valves at assemblage


10.6 Grease crackers for fastening on a valve core


10.7 Repeated check of height of springs


11.1 Removal of a fillet in the cylinder with the help ра звертки     


11.3 Marks of a rod with instructions of number of the cylinder


8. Establish a cam-shaft, platens with коромыслами and pushers (on engines V6).
9. On 4 - cylinder engines adjust backlashes in valves, having established backlashes for the cold engine.

«The previous page
5.9. A head of the block of cylinders-clearings and condition check
The following page»
5.11. Shatunno-piston group-dismantle