Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
4.1. The general data
4.2. Kinds of the repair work which is carried out without dismantle of the engine from the car
4.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step.
4.4. Covers of heads of cylinders – removed and installation
4.5. The platen with коромыслами - removal and installation
4.6. Hydropushers - removal and installation
4.7. A soaking up collector - removal and installation
4.8. A final collector - removal and installation
4.9. A pulley - успокоитель - removal and
4.10. A gear belt - removal and installation
4.11. A forward epiploon коленвала - replacement
4.12. A cam-shaft epiploon - replacement
4.13. Heads of cylinders - removal and installation
4.14. A cam-shaft - removal and installation
4.15. Details клапанного the mechanism - check
4.16. The oil pallet - removal and installation
4.17. The oil pump - removal, check and installation
4.18. A back epiploon - replacement
4.19. A flywheel (a leading disk of the hydrotransformer) -
4.20. Engine support - replacement
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







4-4-kryshki-golovok-cilindrov-snyatoe-i-ustanovka.html

4.4. Covers of heads of cylinders – removed and installation

1. Execute декомпрессию fuel system.

3.4а the Mark About on a pulley and the index


3.4б When division About on a pulley will coincide with the index...
1. A scale of installation of ignition


3.5... And бегунок specifies in the put label the piston of 1st cylinder is in ВМТ a step of compression 1. Бегунок


2. Disconnect the battery from weight.
The right cover
3. Disconnect a hose вентиляций картера (photo)
4. Designate and disconnect from свеч wires, take them aside.
5. Disconnect from a cover hoses and wires.
6. Turn away screws of a cover and remove washers.
4.3 Hoses and wires, which should be disconnected to remove the right cover of a head of cylinders


4.8 Hoses and wires, which should be disconnected to remove the left cover of a head of cylinders


5.3 Lay bolts of platens in cash desk as it should be it installations


7. Uncover, cautiously having opened consolidation.
The left cover
8. Disconnect from a cover a hose сапуна (Photo).
9. Designate and disconnect from свеч wires.
10. Get from wire arms.
11. Turn away 9 screws and uncover.
Installation
12. Clear a cover of the consolidation rests, put in a flute of a cover hermetic and lay a lining. After схватывания hermetic establish a cover and wrap screws.
13. In regular intervals tighten screws in 3-4 receptions.
14. Other procedures are carried out upside-down.
15. Warm up the engine and be convinced of absence of a leak

«The previous page
4.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step.
The following page»
4.5. The platen with коромыслами - removal and installation