Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
4.1. The general data
4.2. Kinds of the repair work which is carried out without dismantle of the engine from the car
4.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step.
4.4. Covers of heads of cylinders – removed and installation
4.5. The platen with коромыслами - removal and installation
4.6. Hydropushers - removal and installation
4.7. A soaking up collector - removal and installation
4.8. A final collector - removal and installation
4.9. A pulley - успокоитель - removal and
4.10. A gear belt - removal and installation
4.11. A forward epiploon коленвала - replacement
4.12. A cam-shaft epiploon - replacement
4.13. Heads of cylinders - removal and installation
4.14. A cam-shaft - removal and installation
4.15. Details клапанного the mechanism - check
4.16. The oil pallet - removal and installation
4.17. The oil pump - removal, check and installation
4.18. A back epiploon - replacement
4.19. A flywheel (a leading disk of the hydrotransformer) -
4.20. Engine support - replacement
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







4-13-golovki-cilindrov-snyatie-i-ustanovka.html

4.13. Heads of cylinders - removal and installation

1. Execute декомпрессию fuel system, disconnect the battery from weight and спейте a liquid.

12.4 Labels й and L on asterisks распре two лов)


12.5б Zapressovka of an epiploon (the same  adaptation, as for an epiploon коленвала is used  )


13.3 Bolts of fastening of a back cover of a gear belt


2. Will remove a gear belt, the case заслонки, всасья вающий a collector, asterisks of cam-shafts.
3. Will turn away bolts and remove a back cover of a belt (photo).
13.7а the Order отпускания bolts of a head of cylinders
1. To a forward part


13.8 Bolt in the bottom part of a head of cylinders


13.14а Orientation of washers of a head of cylinders
1. Towards a head


Removal of the left head
4. Remove the compressor and take aside, without disconnecting a highway.
5. Remove the distributor, the generator, an arm of the generator and a final collector.
6. Remove details клапанного the mechanism.
7. In regular intervals and gradually turn away bolts of a head of cylinders and store them in an initial order (photo).
8. Turn away a small bolt in the bottom part heads (photo) and cautiously remove a head.
The right head
9. Remove the pump of the hydraulic booster and take aside.

13.7б One of ways of storage of bolts on a pattern of a lining of a head of cylinders (it is possible to remove from a new lining). Designate a forward part, and also the right and left parties of a head of cylinders


13.13 Sorientirujte a lining on pins on the block of cylinders


13.14б a tightening Order болтав heads. Bolts 4,5,12 and 13 are longer than the others
1. The right head                       
2. The left head


14.3 Bolts of a face cover.


14.4б... Turn away the central bolt


10. Remove a final collector, details клапанного the mechanism and turn away bolts of a head of cylinders (see above).
11. Turn away a small bolt in the bottom part of a head and cautiously remove a head of cylinders
Installation
12. Carefully clear demountable planes of the block and a head, small roughnesses polish, banish and clear all carving apertures.
13. Lay on the block a new lining (photo).
14. Wrap by hand bolts of a head of cylinders on former places. The flat part of washers of bolts should be turned towards a head of cylinders (photo).
15. Tighten bolts in 5 stages with the set moment in the specified sequence (photo).
16. Other operations are carried out upside-down. Replace oil and the filter.

«The previous page
4.12. A cam-shaft epiploon - replacement
The following page»
4.14. A cam-shaft - removal and installation