4-10-zubchatyjj-remen-snyatie-i-ustanovka.html
4.10. A gear belt - removal and installation1. Execute декомпрессию fuel system and disconnect the battery from weight.
2. Merge cooling liquid.
3. Establish the piston of 1st cylinder in ВМТ a compression step.
4. Remove the air filter and covers of heads of cylinders.
5. Release bolts of platens коромысел.
6. Remove all belts, a casing of the fan and a roller натяжителя a conditioner belt.
7. Remove a pulley-uspokoitel.
8. Disconnect the bottom hose of a radiator from a branch pipe and ослабьте a collar on other end of a branch pipe.
9. Turn away a bolt and remove a branch pipe.
10. Turn away bolts of covers of a gear belt (photo). Bolts should be designated, that at assemblage to establish on former places.
11. Be convinced that all labels on 3 asterisks are combined with motionless indexes (in a kind рисок on covers of a belt and the pump case, a photo). Otherwise tighten коленвал before combination of labels, having screwed a bolt успокоителя.
12. Release a nut of a roller (photo).
13. Remove a belt. Check up freedom of rotation of a roller (photo).
14. Before belt installation turn натяжитель clockwise on 70-80 ° and tighten a counternut (photo)
15. Establish a belt so that the arrow has been turned forward.
16. Combine white risks on a belt with labels on asterisks (photo).
|
10.10а Covers of a gear belt
1. The bottom forward cover (on cars 4x2)
2. The bottom forward cover (on cars 4x4)
3. The top forward cover
4. A back cover
|
|
10.106 Gear belt and drive details
1. The block of cylinders
2. An adjusting hairpin
3,14. An asterisk
4. A spring
5. Натяжитель
6,8,13. A washer
7. A leading asterisk
9. A pulley
10,11,15. A cover
12. A conic washer
|
The fastening drawing
|
Number позгиции in which
вворачиватся; a bolt
|
|
1,2,3,4,5 20, 22, 23
|
|
6,24
|
|
7,8,9,10,21 1
|
|
15,16,17.18, 1 11,12,13
|
|
19,25
|
|
10.11 Adjusting labels on belt asterisks
1,3,6-labels
2. A back cover
4,9. The left (right) cam-shaft
5. The piston of 1 th cylinder is in ВМТ a compression step
7. The oil pump
8. A leading asterisk
|
|
10.12 Nut of a roller натяжителя a belt
|
Adjustment
17. Release a counternut натяжителя and again turn натяжитель on 70-80 ° clockwise (photo).
18. Slowly turn коленвал clockwise on 2-3 turns and again expose the piston of 1 th cylinder in ВМТ a compression step. If the big resistance to rotation return коленвал in a starting position is felt and check up combination of labels of a belt and pulleys.
19. Keeping натяжитель, release a counternut.
20. Put to натяжителю щуп 0,35 mm (photo).
21. Slowly turn коленвал while щуп there will be no between натяжителем and a belt (photo).
|
10.14 Preliminary adjustment натяжителя
|
|
10.16а Combination рисок a belt with labels on asterisks of cam-shafts.
|
|
10.16б Before releasing a counternut be convinced that the label on a leading asterisk is located opposite risks on the case of the oil pump
|
|
10.20 Put щуп in the specified place...
1. Коленвал
2. A belt
3. Width of 0,500 mm
4. A thickness of 0,35 mm
5. Щуп
6. An appendix place щупа
7. A roller натяжителя
|
|
10.25 At check to put effort in the middle between asterisks. The deflection should correspond to the specified
1,2. Cam-shafts
3. A belt
|
|
10.17 Natjazhitel of a belt
1. A spring hook
2. A kind on an arrow And
3. A hairpin
4. A spring
|
|
10.21... Also turn коленвал while щуп it will not appear between натяжителем and a belt
1. Щуп
2. Коленвал
3. A belt
4. A roller
|
22. Keeping натяжитель, tighten a counternut.
23. Turn коленвал and clean щуп.
24. Slowly turn коленвал clockwise on 2-3 turns and again expose the piston 1 of th tsilin - I дра in ВМТ a compression step.
25. Check up a belt tension under the scheme (photo)
26. Establish all removed details.
|