Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
3.1. The general data
3.2. Kinds of the repair work which is carried out without dismantle of the engine from the car
3.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step.
3.4. A cover of a head of cylinders - removal and installation
3.5. The platen with коромыслами - removal and installation
3.6. The platen with коромыслами - dismantling and assemblage
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and коромысла - check
3.9. Springs of valves and маслосъемные caps - replacement
3.10. A soaking up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A pulley коленвала - removal and installation
3.17. A forward epiploon коленвала - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a leading disk of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







3-7-raspredval-snyatie-i-ustanovka.html

3.7. A cam-shaft - removal and installation

1. Uncover heads of cylinders.
2. Turn out candles.
3. Establish the piston of 1st cylinder in ВМТ a compression step.
4. Put labels on a chain and a cam-shaft asterisk. If the head does not act in film, infringement of a relative positioning of these details is not supposed.
5. Prepare a wooden wedge with the sizes 250x19 mm and width on the one hand 30-37 mm, and with another - 25 mm.
6. Get заглушку and turn away an asterisk bolt, remove a cam of a drive of the fuel pump (photo).
7. Расклиньте a chain, having entered a wedge a narrowed part downwards. A convergence of a chain from a gear wheel коленвала. It is not supposed.
8. Cautiously remove an asterisk, holding a chain which should remain on a wedge (photo).
9. Remove platens with коромыслами.
10. Remove a cam-shaft, having paid attention to pin orientation at an end face.
11. Check up a cam-shaft condition (see more low).
12. Establish a cam-shaft, without breaking initial orientation of a pin. Preliminary grease support and necks of a shaft (photo).
13. Establish platens коромысел. Tighten bolts by hand. Two average bolts tighten with the moment 17 Н.м.
14. Dress a chain on an asterisk, cautiously having removed from a wedge and dress an asterisk on a cam-shaft. The pin should come into the second deepening of an asterisk, and the labels put before dismantling should be combined.
15. Clean a wedge and wrap a bolt, establish a cam of a drive of the fuel pump. Tighten a bolt with the set moment. Grease заглушку with hermetic and establish in a head of cylinders.
16. Tighten bolts of platens коромысел with the set moment.
17. Adjust valves.
18. Establish a cover.
19. Warm up the engine and again adjust backlashes taking into account norms for the heated-up engine.

«The previous page
3.6. The platen with коромыслами - dismantling and assemblage
The following page»
3.8. A cam-shaft, support and коромысла - check