Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
3.1. The general data
3.2. Kinds of the repair work which is carried out without dismantle of the engine from the car
3.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step.
3.4. A cover of a head of cylinders - removal and installation
3.5. The platen with коромыслами - removal and installation
3.6. The platen with коромыслами - dismantling and assemblage
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and коромысла - check
3.9. Springs of valves and маслосъемные caps - replacement
3.10. A soaking up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A pulley коленвала - removal and installation
3.17. A forward epiploon коленвала - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a leading disk of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







3-6-valik-s-koromyslami-razborka-i-sborka.html

3.6. The platen with коромыслами - dismantling and assemblage

1. Remove all bolts except for two bolts on both ends.
2. Keeping the platen, cautiously get 2 extreme bolts, allowing to be straightened by springs.
3. Remove коромысла and designate so that at assemblage to establish on former places.
4. Replace platens if on them there are deterioration signs.

6.5а Orientation of platens коромысел at assemblage (engine Z24)
1. Grooves
2. Кернения
3. The platen of final valves
4. The platen of inlet valves
5. To a forward part of the engine


6.5б Adjusting labels on arms of platens and on a head of cylinders 1. To a forward part of the engine 2. Labels on arms 3. Labels on a head of cylinders


6.5в Orientation скоб at assemblage of platens with коромыслами (engine K24J 1,2. Cut 3. From outside inlet valves 4. From outside final valves





7.6 Otvorachivanie of a bolt of an asterisk of a cam-shaft


7.8 Fixing of a chain by a wedge


7.12 Before installation grease cam-shaft necks


5. Establish the platen in a forward arm, combine apertures and insert bolts. On the platen of inlet valves grooves are provided. At assemblage establish platens so that кернения at their end faces have been turned upwards. Arms establish being guided on labels (photo).
6. Dress коромысла, compress a spring and establish back arms, insert bolts. Establish platens and a cover upside-down.

«The previous page
3.5. The platen with коромыслами - removal and installation
The following page»
3.7. A cam-shaft - removal and installation