Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
3.1. The general data
3.2. Kinds of the repair work which is carried out without dismantle of the engine from the car
3.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step.
3.4. A cover of a head of cylinders - removal and installation
3.5. The platen with коромыслами - removal and installation
3.6. The platen with коромыслами - dismantling and assemblage
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and коромысла - check
3.9. Springs of valves and маслосъемные caps - replacement
3.10. A soaking up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A pulley коленвала - removal and installation
3.17. A forward epiploon коленвала - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a leading disk of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







3-3-poryadok-ustanovki-porshnya-1-go-cilindra-v-vmt-takta-szhatiya.html

3.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step.

1. On a pulley коленвала the mark for exhibiting of the piston of 1 th cylinder in ВМТ a compression step is provided.
2. Piston installation (or pistons) in ВМТ a compression step is an integral part of many procedures.
3. Translate the check point lever in neutral position. Disconnect a high-voltage wire of the coil of ignition from the central conclusion of a cover of the distributor and connect to weight on the block of cylinders.

3.5б the Scale on a pulley (engine K24) 1. A label of red colour 2. A scale for ignition installation


4. Uncover the distributor and find on a cover position of a high-voltage wire of a candle of 1 th cylinder. If this conclusion is not numbered, define it on a wire from a spark plug.
5. Turn коленвал a key or a starter so that the mark in a pulley was combined with a label About on a scale. A normal direction of rotation of the engine - clockwise (photo).
5. If бегунок specifies in a label put on the case of the distributor the piston of 1 th cylinder is in ВМТ a compression step. Otherwise tighten коленвал on one complete revolution clockwise (360 °) and establish the piston of 1st cylinder in ВМТ a compression step.
6. Now it is possible to expose in ВМТ a step of compression and other pistons, turning коленвал on 180 ° and observing an operating procedure of cylinders.

«The previous page
3.2. Kinds of the repair work which is carried out without dismantle of the engine from the car
The following page»
3.4. A cover of a head of cylinders - removal and installation