Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
3.1. The general data
3.2. Kinds of the repair work which is carried out without dismantle of the engine from the car
3.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step.
3.4. A cover of a head of cylinders - removal and installation
3.5. The platen with коромыслами - removal and installation
3.6. The platen with коромыслами - dismantling and assemblage
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and коромысла - check
3.9. Springs of valves and маслосъемные caps - replacement
3.10. A soaking up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A pulley коленвала - removal and installation
3.17. A forward epiploon коленвала - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a leading disk of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







3-19-cep-i-zvezdochki-snyatie-i-ustanovka.html

3.19. A chain and asterisks - removal and installation

Removal
1. Remove a forward cover.
2. Turn away bolts натяжителя, a boot and успокоителя, remove these details (photo).
3. Reject a bolt and remove a cam-shaft asterisk (see above).
4. Remove a chain.
5. Remove маслоотражатель, a gear wheel of a drive of the oil pump, and a leading asterisk (photo).
6. Check up a condition of teeths of asterisks, having compared profiles of teeths on both parties. At detection крючковатости asterisk teeths replace.
7. The chain varies together with the worn out asterisks, or through each 48000 km. Also it is necessary to replace a chain at detection of signs of deterioration of rollers.
8. Establish an asterisk on a cam-shaft and check up its axial люфт which should not exceed 0,2 mm.

19.5 Removal of a leading asterisk


19.2 Chain of a drive of a cam-shaft
1. Натяжитель
2. Успокоитель the left
3. Успокоитель the right
4. Маслоотражатель
5. A gear wheel of a drive of the oil pump
6. A leading asterisk
7. A chain


9. Check up a condition натяжителя and успокоителей, if necessary replace.
Installation
10. Turn a cam-shaft so that valves of 1st cylinder have been closed. Коленвал establish so that the piston of 1 th cylinder was in ВМТ.
11. Establish успокоители.
12. Establish маслоотражатель, a gear wheel of a drive of the oil pump, and a leading asterisk on a sock коленвала. Be convinced that adjusting labels on a leading asterisk are turned forward (photo).
13. Before installation of a chain turn коленвала is not supposed.

19.12 At assemblage шпонка the label on an asterisk - forward should be turned upwards, and


19.14а On engine Z24i the link of a chain with distinctive colouring should be combined with a label on a cam-shaft asterisk, and the adjusting pin of a cam-shaft should come into an aperture at number 2


19.14г On all engines a link of a chain with distinctive colouring should be it is combined with a label on a leading asterisk


14. Dress a chain on a cam-shaft asterisk, then get on a leading asterisk. Tighten a bolt of an asterisk of a cam-shaft. At assemblage have in view of the following:
. Shponka коленвала should be turned upwards.
. Links of a chain with distinctive colouring should be combined with labels on asterisks, and settle down on the right, if to look in front of (photo).
. The adjusting pin of a cam-shaft should come into an aperture in an asterisk at number 2 (photos).
15. Establish натяжитель, adjust position left успокоителя so that a backlash between the case натяжителя and a boot was absent (photo).
16. Establish a forward cover.

«The previous page
3.18. A forward cover - removal and installation
The following page»
3.20. The oil pallet - removal and installation