Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
3.1. The general data
3.2. Kinds of the repair work which is carried out without dismantle of the engine from the car
3.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step.
3.4. A cover of a head of cylinders - removal and installation
3.5. The platen with коромыслами - removal and installation
3.6. The platen with коромыслами - dismantling and assemblage
3.7. A cam-shaft - removal and installation
3.8. A cam-shaft, support and коромысла - check
3.9. Springs of valves and маслосъемные caps - replacement
3.10. A soaking up collector - removal and installation
3.11. A final collector - removal and installation
3.12. A head of cylinders - removal
3.13. A head of cylinders - installation
3.14. The oil pump - removal and installation
3.15. The oil pump - check
3.16. A pulley коленвала - removal and installation
3.17. A forward epiploon коленвала - replacement
3.18. A forward cover - removal and installation
3.19. A chain and asterisks - removal and installation
3.20. The oil pallet - removal and installation
3.21. A flywheel (a leading disk of the hydrotransformer) - removal and installation
3.22. A back epiploon - replacement
3.23. Engine support - replacement
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







3-11-vypusknojj-kollektor-snyatie-i-ustanovka.html

3.11. A final collector - removal and installation

1. Disconnect tubes эжекции air, remove the case of valves (if it is provided).
2. Disconnect the channel connecting a collector and the air filter.
3. Remove a thermal guard.
4. Disconnect a tube рециркуляции (photo).
5. Lift a forward part of the car and establish on supports.
6. Disconnect a forward exhaust pipe.
7. Disconnect wires from свеч from outside a final collector.
8. Turn away bolts and collector nuts.

11.4 Tubes эжекции air (at the left) and рециркуляции (on the right) on a final collector of engine  Z24i


12.13а Sequence of easing of bolts of a head of cylinders on engines Z24


12.13б Sequence of easing of bolts of a head of cylinders on engines K24


13.2 Head of cylinders of engine K24
1 Platens коромысел and коромысла valves
2. A head of cylinders
3. A lining
4. A bolt
5. A cam-shaft
6. A saddle
7. The directing plug
8. A basic washer
9. A maslosemnyj cap
10. Crackers
11. A plate
12. Inlet


9. Disconnect a collector.
10. Clear a collector of the consolidation rests.
11. Establish on a head of cylinders a new lining. Tighten by hand bolts and nuts.
12. In 3-4 receptions tighten bolts and nuts with the set moment. Tighten from the centre to periphery in a cross order.
13. Other operations are carried out upside-down.
20. Warm up, the engine and be convinced of tightness of connections of a collector.

«The previous page
3.10. A soaking up collector - removal and installation
The following page»
3.12. A head of cylinders - removal