Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
2.1. Introduction
2.2. Maintenance service terms
2.3. An order of performance of adjustments - broad-brush observations
2.4. Check of level of liquids
2.5. Check of level of a liquid in automatic transmission
2.6. Check of level of a liquid of the hydraulic booster of a wheel
2.7. Check of tyres (through each 400 kilometres or weekly)
2.8. Care of the battery
2.9. Care of cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and the oil filter
2.14. Check and adjustment of backlashes of valves
2.15. Running gear and steering greasing
2.16. Suspension bracket and steering check
2.17. Check карданного a shaft
2.18. Exhaust system check
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in a manual transmission
2.21. Check of level of oil in a distributing box
2.22. Check of level of oil and картередифференциала (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and the ventilation filter картера
2.30. Replacement of the fuel filter
2.31. Filter replacement эжекционного the system valve доокисления exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case throttle заслонки
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Oil replacement in a distributing box
2.36. Oil replacement in a manual transmission
2.37. Oil replacement in a reducer back (or forward) the bridge
2.38. Replacement трансмиссионной liquids! In automatic transmission
2.39. Greasing replacement in naves of forward wheels and check of bearings (only for rear-wheel cars)
2.40. Replacement of a cooling liquid
2.41. Check and replacement of a zolotnik of ventilation картера
2.42. Replacement свеч ignitions
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and бегунок a rotor - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. The oxygen gauge
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system


2.39. Greasing replacement in naves of forward wheels and check of bearings (only for rear-wheel cars)

1. Люфты in nave bearings check each time at lifting of a forward part of the car.
2. Turn a wheel and check up rotation freedom люфты.
3. If at качании wheels in a vertical plane it is felt люфт it is necessary to check up bearings to replace greasing in a nave
4. Remove a wheel
5. Remove a support, take aside and fix.
6. Выпрессуйте a cap naves (photo).

39.6 Removal of a cap of a nave

39.7 Nave and the bearing of a forward wheel
1. An epiploon
2. The internal bearing
3. A nave
4. The external bearing
5. A washer
6. A ring
7. Шплинт
8. A cap
9. An adjusting nut
10. A brake disk  
11. A brake board

7. Расшплинтуйте a  cap  of an adjusting  nut (photo).
8. Turn away a nut and remove a washer.
9. Submit a nave on itself and push back, get the external bearing.
10. Remove a nave from a pin of a rotary fist.
11. Hook a screw-driver and get an epiploon (photo). Pay attention to epiploon orientation in a nave.
12. Get the internal bearing.
13. Wash out bearings and a nave from greasing, clear a pin.
14. Check up a condition of rollers and external holders of bearings in naves. In case of damages on their external holders it is necessary выпрессовать (it is carried out on a car repair shop) and to replace bearings.
15. Put in bearings refractory greasing, carefully having filled space in a holder of rollers (photo).
16. Grease places of landing of bearings on a pin and расточку under an epiploon.

39.11 Extraction of an epiploon of a nave

17. Put greasing for holders of bearings, having covered edges of holders and having created a fillet for preservation of greasing in bearings.
18. Insert the greased internal bearing and put greasing on its external part.
19. Запрессуйте a new epiploon.
20. Establish a nave and dress the external bearing.
21. Dress a washer and tighten a nut with the moment 3 Н.м.
22. Turn a nave in both directions.
23. Believe the moment of an inhaling and again turn a nave in both directions. Check up the resistance moment проворачиванию which should remain equal 3 Н.м.
24. Wrap a nut on 45 °.
25. Dress корончатый a cap and зашплинтуйте. If necessary tighten a nut clockwise that шплинт has passed in grooves of a cap and in a pin aperture.
26. Bend шплинт so that it did not touch a nave cap.

39.15 Greasing of bearings of a nave

40.4 Ventilating valve of system of cooling on engines V6

27. Напрессуйте a nave cap, having tracked safety of a sealing ring.
28. Dress a wheel, tighten nuts and having shaken, check up люфт in bearings. Lower the car.

«The previous page
2.38. Replacement трансмиссионной liquids! In automatic transmission
The following page»
2.40. Replacement of a cooling liquid