Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
2.1. Introduction
2.2. Maintenance service terms
2.3. An order of performance of adjustments - broad-brush observations
2.4. Check of level of liquids
2.5. Check of level of a liquid in automatic transmission
2.6. Check of level of a liquid of the hydraulic booster of a wheel
2.7. Check of tyres (through each 400 kilometres or weekly)
2.8. Care of the battery
2.9. Care of cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and the oil filter
2.14. Check and adjustment of backlashes of valves
2.15. Running gear and steering greasing
2.16. Suspension bracket and steering check
2.17. Check карданного a shaft
2.18. Exhaust system check
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in a manual transmission
2.21. Check of level of oil in a distributing box
2.22. Check of level of oil and картередифференциала (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and the ventilation filter картера
2.30. Replacement of the fuel filter
2.31. Filter replacement эжекционного the system valve доокисления exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case throttle заслонки
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Oil replacement in a distributing box
2.36. Oil replacement in a manual transmission
2.37. Oil replacement in a reducer back (or forward) the bridge
2.38. Replacement трансмиссионной liquids! In automatic transmission
2.39. Greasing replacement in naves of forward wheels and check of bearings (only for rear-wheel cars)
2.40. Replacement of a cooling liquid
2.41. Check and replacement of a zolotnik of ventilation картера
2.42. Replacement свеч ignitions
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and бегунок a rotor - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. The oxygen gauge
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system


2.27. Drive belts - check, adjustment and replacement

1. For a drive of units belts клинообразного sections are used.
2. The quantity of the belts established on the car depends on type of the engine and from a car complete set. The belt drive is provided for the generator, the pump of a cooling liquid, the compressor of the conditioner and the wheel hydraulic booster.

26.4 Nozzles of the air filter with the thermostat

26.5 Scheme of work of the thermostat 1. To the gauge of temperature of air 2. A vacuum drive 3. It is opened 4. It is closed 5. Cold air 6. To the carburettor 7. Делительная заслонка 8. Hot air from a final collector

3. The condition of belts is checked to the touch and survey (having shined belts with a small lamp). Check up presence отслоения the rubber pasted overlay on both parties of a basis to belts of an anguish of a basis on end faces of a tape of a belt, hardening, damages of a surface of a belt (cracks, a separation and deterioration of paths, the photo see). Check up also presence of deterioration and стеклования a belt material owing to which on a belt luster is observed. Overwind a belt and examine from both parties.
4. Check up a belt tension. At distance centre to centre pulleys from 170 to 280 mm the belt deflection should be about 6 mm. If this distance from 300 to 400 mm the deflection should be about 13 mm (photo).
5. For tension adjustment special devices (photo) are provided.
6. For adjustment it is necessary to release bolts of fastening of the unit and to move the unit, having pulled a belt (or to rotate an adjusting bolt). Tighten boats of fastening and check up a tension. If a tension in norm tighten bolts fastenings (photo). The tension of a gear belt is regulated by roller moving натяжителя.

27.3 Some characteristic signs of deterioration of a belt.
1. Cracks
2. Стеклование
3. Greasing hit
4. An anguish of a basis of a belt

7. It is recommended to change all belts simultaneously.

«The previous page
2.26. Check of the thermostat of the air filter
The following page»
2.28. Check of seat belts