Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
2.1. Introduction
2.2. Maintenance service terms
2.3. An order of performance of adjustments - broad-brush observations
2.4. Check of level of liquids
2.5. Check of level of a liquid in automatic transmission
2.6. Check of level of a liquid of the hydraulic booster of a wheel
2.7. Check of tyres (through each 400 kilometres or weekly)
2.8. Care of the battery
2.9. Care of cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and the oil filter
2.14. Check and adjustment of backlashes of valves
2.15. Running gear and steering greasing
2.16. Suspension bracket and steering check
2.17. Check карданного a shaft
2.18. Exhaust system check
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in a manual transmission
2.21. Check of level of oil in a distributing box
2.22. Check of level of oil and картередифференциала (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and the ventilation filter картера
2.30. Replacement of the fuel filter
2.31. Filter replacement эжекционного the system valve доокисления exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case throttle заслонки
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Oil replacement in a distributing box
2.36. Oil replacement in a manual transmission
2.37. Oil replacement in a reducer back (or forward) the bridge
2.38. Replacement трансмиссионной liquids! In automatic transmission
2.39. Greasing replacement in naves of forward wheels and check of bearings (only for rear-wheel cars)
2.40. Replacement of a cooling liquid
2.41. Check and replacement of a zolotnik of ventilation картера
2.42. Replacement свеч ignitions
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and бегунок a rotor - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. The oxygen gauge
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system


2.15. Running gear and steering greasing

1. Accessories to greasing are shown on a photo. 15.1 Accessories to greasing
2. To running gear and steering greasing it is applied universal литиевые greasings  to Greasing spherical support of levers of a forward suspension bracket, tips of steering draughts, forward and back карданная transfer (on cars With the wheel formula 4x4) are subject.
3. The place of greasing of the top support is in the top part of the case support (photo), for greasing it is necessary to remove a wheel. Access to a butterdish of the bottom support is provided through an aperture in the lever (photo). An aperture for greasing tips of steering draughts turn out заглушку (photo). On карданной to transfer hinges and шлицевое sliding connection (photo) are greased.
4. Lift the car and establish on supports.
5. Turn out заглушки and screw butterdishes (on a part of cars).
6. Squeeze out a few greasings from a syringe and wipe absolutely.

15.3а the Carving aperture under a butterdish for greasing of the top support is muffled by a stopper

15.3в Zaglushka of an aperture under a butterdish in a draught tip

7. Grease with a syringe all connections. Spherical support шприцуйте until then while greasing will not fill rubber covers (it is felt on pressing). If greasing it vyho-is put from a butterdish tighten a butterdish or turn out and check up cleanliness of the valve of a butterdish.
8. Remove the greasing rests.
15.3г  Zaglushka of an aperture under a butterdish on карданном the hinge

15.3б the Aperture in the lever for greasing of the bottom support (on а/м early releases)

15. Зг the Butterdish шлицевого connections

9. Grease a cable and levers of a manual brake.
10. Lower the car.
11. Grease rubbing details of locks of a cowl and a back door, grease the terminations of cables.
12. Grease loops of doors with several drops of oil for the engine.
13.  Cylindrical  switches  of locks  of doors are greased with aerosol graphite greasing.

«The previous page
2.14. Check and adjustment of backlashes of valves
The following page»
2.16. Suspension bracket and steering check