Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
2.1. Introduction
2.2. Maintenance service terms
2.3. An order of performance of adjustments - broad-brush observations
2.4. Check of level of liquids
2.5. Check of level of a liquid in automatic transmission
2.6. Check of level of a liquid of the hydraulic booster of a wheel
2.7. Check of tyres (through each 400 kilometres or weekly)
2.8. Care of the battery
2.9. Care of cooling system
2.10. Check of brushes of screen wipers
2.11. Check of a condition of the hoses located in a motor compartment.
2.12. Check and adjustment of a pedal of a brake
2.13. Replacement of oil and the oil filter
2.14. Check and adjustment of backlashes of valves
2.15. Running gear and steering greasing
2.16. Suspension bracket and steering check
2.17. Check карданного a shaft
2.18. Exhaust system check
2.19. Check and adjustment of a pedal of coupling
2.20. Check of level of oil in a manual transmission
2.21. Check of level of oil in a distributing box
2.22. Check of level of oil and картередифференциала (or in a reducer of the back bridge)
2.23. Shift of wheels
2.24. Check of brakes
2.25. Check of fuel system
2.26. Check of the thermostat of the air filter
2.27. Drive belts - check, adjustment and replacement
2.28. Check of seat belts
2.29. Replacement of the air filter and the ventilation filter картера
2.30. Replacement of the fuel filter
2.31. Filter replacement эжекционного the system valve доокисления exhaust gases
2.32. Replacement of the filter of a tank with an absorber
2.33. Check of fastening of the case throttle заслонки
2.34. Check and adjustment of turns of idling (engines with fuel injection)
2.35. Oil replacement in a distributing box
2.36. Oil replacement in a manual transmission
2.37. Oil replacement in a reducer back (or forward) the bridge
2.38. Replacement трансмиссионной liquids! In automatic transmission
2.39. Greasing replacement in naves of forward wheels and check of bearings (only for rear-wheel cars)
2.40. Replacement of a cooling liquid
2.41. Check and replacement of a zolotnik of ventilation картера
2.42. Replacement свеч ignitions
2.43. High-voltage wires - check and replacement
2.44. A cover of the distributor and бегунок a rotor - check and replacement.
2.45. Check and installation of the moment of ignition.
2.46. The oxygen gauge
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







2-11-proverka-sostoyaniya-shlangov-raspolozhennykh-v-motornom-otseke.html

2.11. Check of a condition of the hoses located in a motor compartment.

The general data
1. Conditioner hoses are checked and vary only in car-care centre service.

10.2 Extraction of a scraper from щеткодержателя


2. Under the influence of heats in a motor compartment gradually there is a hardening and destruction of the rubber and plastic hoses which are ensuring functioning of various units of the engine. It is necessary to check periodically a condition of hoses, presence on them of cracks and hardening, easing of connections, tightness infringement. The procedure for test of hoses of system of cooling is described in section 9.
3. A part of hoses fasten by means of collars. Check durability of an inhaling of collars as fastening easing leads to tightness infringement. In those places in which collars are not provided, check reliability of consolidation of a hose on unions, elasticity loss in such connections owing to swelling or hardening of hoses is not supposed, tightness of connection otherwise is broken.
Vacuum hoses
4. Vacuum hoses can be distinguished on colour, or on the colour strips pasted on them. For various systems of the engine vacuum hoses with various in the thickness of walls, resistance to compression by atmospheric pressure and thermal stability are used. At replacement track that new vacuum hoses in accuracy corresponded to the replaced.
5. Frequently the hose can be checked up only after removal from the car. If some hoses act in film, preliminary put labels on interfaced the union and hoses subsequently not to break their relative positioning.
6. At check of a condition of vacuum hoses at the same time examine also plastic tees. Check up presence on them of cracks, and also hose deformations in a place прилегания to the union of a tee which can cause tightness infringement.

12.1 Height (h) and a free wheeling () pedals of a brake 1. A pusher 2. The switch of a signal of braking З, 4 Counternut 5. A floor



7. For check of leaks listen through a piece of a hose with internal diameter about 6 mm, having put a hose to a checked place. Characteristic "hissing" will specify in leak presence.
Fuel hoses
8. Check up a condition of rubber fuel hoses, presence on them of damages.
9. At replacement of a fuel highway on инжекторных engines the new highway should correspond in accuracy applied in fuel system of engines of the given type.
10. At replacement of hoses always establish collars with screw fastening.
Metal tubes
11. Metal tubes are usually used in a fuel highway for connection of the fuel pump with a regulator of pressure of fuel on a comb of atomizers. Check up presence on tubes of the braided sites and small arising cracks.
12. At replacement it is necessary to establish only seamless steel tubes. Tubes from copper or aluminium do not approach, as do not maintain vibrating loadings from the engine.
13. Check up a condition of metal tubes and unions of system of a hydrodrive of brakes in junctions with the main brake cylinder and дозатором, presence of cracks and ослабших connections is not supposed.

«The previous page
2.10. Check of brushes of screen wipers
The following page»
2.12. Check and adjustment of a pedal of a brake