Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
17.1. Specifications
17.2. The general data
17.3. Search of malfunctions - the general of data
17.4. Safety locks - the general data
17.5. Fusible crosspieces - the general data
17.6. The relay - the general data
17.7. Switches - check
17.8. Indexes of turns and the alarm system - the general data
17.9. Headlights - adjustment
17.10. Headlights - removal and installation
17.11. Lamps - replacement
17.12. A sound signal - check
17.13. A sound signal - removal and installation
17.14. A windscreen cleaner - the general of data
17.15. The electric motor of a cleaner of glass - removal and installation
17.16. Стеклоомыватель - removal and installation
17.17. The block of switches on a steering column - removal and installation
17.18. The ignition switch - removal and installation
17.19. A guard of devices - removal and installation
17.20. The receiver - removal and installation
17.21. Прикуриватель - removal and installation
17.22. The block of switches of illumination - removal and installation
17.23. The alarm system switch - removal and installation
17.24. The switch of a heater of back glass - removal and installation
17.25. A thermoelement of heating of back glass - removal and installation
17.26. Safety pillows - the general data
17.27. Schemes the assembly and electric basic
 







17-25-termoehlement-obogreva-zadnego-stekla-snyatie-i-ustanovka.html

17.25. A thermoelement of heating of back glass - removal and installation

1. The thermoelement consists of a set horizontal проволок, introduced in glass at a formation stage.
2. Small damages проволок can be eliminated independently, to remove glass it is not required.
3. To check up work of a heater of back glass start the engine and include a heater.
4. Connect to weight one of wires of a control lamp, and with other wire concern a heater wire.
5. Displace a wire along a wire from right to left, - brightness of a luminescence of a lamp thus should accrue. If brightness of a lamp is identical on both ends of a wire of a thermoelement it is necessary to check up connection of a heater with weight. All a wire should be checked up not less than two places.
6. For heater repair special spending paste with silver powder (is available on sale) is required.
7. Switch off a heater and wait cooling.
8. Slightly заполируйте the damaged site a soft steel sponge, wipe spirit.
9. Paste pieces of a sticky tape from both parties of the damaged site so that the backlash between pieces in accuracy coincided with a wire line on the damaged site.
10. Dip into paste a poster feather and spend a line on a backlash between tape pieces so that the strip of paste blocked the damaged site a little.
11. Cautiously remove pieces of a tape and dry the put path an air soldering iron with temperature 250-350 ° With during 1-2 mines from distance of 2-3 sm to glass.
12. If necessary restore colour of the damaged site iodine tincture. The restored heater can be included not less than in 24 hours.


«The previous page
17.24. The switch of a heater of back glass - removal and installation
The following page»
17.26. Safety pillows - the general data