Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. The general data
14.3. Колодки disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum-type brakes - replacement колодок
14.7. The wheel cylinder of back drum-type brakes - removal, dismantling and installation
14.8. See гл. 1
14.9. Disks of back brakes - check, removal and installation
14.10. Колодки a manual brake (on back disk brakes) - removal, installation and adjustment
14.11. The main cylinder of brakes - removal, dismantling and installation
14.12. A regulator of pressure of brakes - removal and installation
14.13. A hydrodrive highway - check and replacement
14.14. Prorolling of brakes
14.15. The vacuum amplifier of brakes - the general data and check
14.16. The vacuum amplifier of brakes - removal and installation
14.17. A manual brake - adjustment
14.18. The lever of a manual brake - removal and installation
14.19. Cables of a manual brake - removal and installation
14.20. The switch of a signal of braking - removal and installation
14.21. Antiblocking system (ABS) - the general data and access to codes.
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







14-6-zadnie-barabannye-tormoza-zamena-kolodok.html

14.6. Back drum-type brakes - replacement колодок

1. Lift a back part of the car and establish on supports. Release a manual brake.
2. Remove a wheel.
3. If necessary reduce колодки a regulator (Gl. 1)
4. Remove a drum for what rotating a drum, knock on it with a hammer with soft brisk in a direction outside. If the drum does not give in to removal displace it, in regular intervals wrapping bolts М8 х 1,25 in special carving apertures (photo).

4.5б Check of a thickness of a disk. Measure a thickness in several places


4.13б disk and nave Division


5.4 Removal of a drum by means of auxiliary bolts


5. Cautiously clear a drum of a dust and a dirt.
6. Remove clamping springs колодок for what press a cap and turn on 90 ° (photo).
7. Remove the top coupling springs колодок (photo).
8. Dissolve колодки and get распорку (photo).

5.6 Removal of clamping springs колодок


9. In addition dissolve колодки and get them from grooves in a regulator and pistons. Fix pistons from выдвигания from cylinders (that at assemblage not to pump over a hydrodrive).
10. Disconnect from the lever a cable of a manual brake.
11. A pedal of a brake do not press, otherwise pistons leave the cylinder.
12. Check up a condition of covers of the cylinder and presence of a leak of a liquid. If necessary repair or replace cylinders.

5.7б the Top spring directing and a cable peгулятора


13. Grease a regulator carving колодок brake a liquid.
14. Before assemblage slightly grease rubbing places ю boats with brake greasing, without supposing hit on pi зиновые a detail.
5.7а Details of a back drum-type brake полнопоиволного the car "Terrann I/Pathfinder" 1. The adjusting lever 2. A spring 3. A basic washer of a spring 4. A clamping spring 5. A cap of a spring 6. A drum 7. An adjusting cable with a spring 8,14. A spring 9,12


5.8 Removal распорки колодок


5.16 Marks with instructions of limiting internal diameter of a drum


15. Establish springs, enter into a regulator groove the bottom end face back колодки then the bottom end face of a lobby колодки, move apart колодки and enter into grooves of pistons of the wheel cylinder. Establish other details (photo).
16. Establish a drum and a wheel.
17. Adjust a backlash between колодками and drums some times having lifted and having lowered the lever of a manual brake. If necessary remove air from brakes. Lower the car.


«The previous page
14.5. A brake disk - check, removal and installation
The following page»
14.7. The wheel cylinder of back drum-type brakes - removal, dismantling and installation