Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. The general data
14.3. Колодки disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum-type brakes - replacement колодок
14.7. The wheel cylinder of back drum-type brakes - removal, dismantling and installation
14.8. See гл. 1
14.9. Disks of back brakes - check, removal and installation
14.10. Колодки a manual brake (on back disk brakes) - removal, installation and adjustment
14.11. The main cylinder of brakes - removal, dismantling and installation
14.12. A regulator of pressure of brakes - removal and installation
14.13. A hydrodrive highway - check and replacement
14.14. Prorolling of brakes
14.15. The vacuum amplifier of brakes - the general data and check
14.16. The vacuum amplifier of brakes - removal and installation
14.17. A manual brake - adjustment
14.18. The lever of a manual brake - removal and installation
14.19. Cables of a manual brake - removal and installation
14.20. The switch of a signal of braking - removal and installation
14.21. Antiblocking system (ABS) - the general data and access to codes.
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







14-5-disk-tormoza-proverka-snyatie-i-ustanovka.html

14.5. A brake disk - check, removal and installation

Check
1. Release nuts of wheels, lift the car and establish on supports. Remove wheels.
2. Remove a support with the cylinder and take aside.
3. Check up a disk condition. At detection of traces of deep development (depth more than 0,38 mm) remove a disk and прошлифуйте (photo).
4. Check up palpation (especially if at braking vibrations were felt) with the help стрелочного the indicator (photo). If palpation on the indicator exceeds norm remove a disk and прошлифуйте.

Attention!
The disk in general is recommended to be removed periodically and прошлифовывать on it is dependent on indicator indications. At least it can be made by hand a small skin (photo) to reduce a roughness.

5. After polishing the thickness of a disk should not be less maximum permissible (the thickness is cast on a disk, a photo).
Removal
6. Remove a dustproof cover of a nave.
7. Remove шплинт.

3.12 Installation of the piston in the cylinder 1. The cylinder 2. The piston 3. A cuff 4. A cover


4.4а Check of palpation of a disk


8. Remove a cap.
9. Turn away a nut of a nave and remove a washer.
10. Remove the external bearing.
11. Remove a nave in gathering with a disk.
12. If the disk is перешлифовываться get: an epiploon.

4.4б disk Polishing by hand


4.5а the Place of drawing of a limiting thickness of a disk


4.13а Bolts of fastening of a disk to a nave


13. If the disk varies, separate it from a nave for what turn away bolts, обстучите on nave edge, hook screw-drivers and remove a disk (photo). If to separate a disk in such a way it is not possible, grease a joint of a disk and a nave with a getting liquid.
Installation
14. Establish a disk on a nave and screw bolts.
15. In regular intervals and gradually tighten bolts to the full.
16. Other operations are carried out according to Gl.11.


«The previous page
14.4. A brake support - removal, dismantling and installation
The following page»
14.6. Back drum-type brakes - replacement колодок