Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. The general data
14.3. Колодки disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum-type brakes - replacement колодок
14.7. The wheel cylinder of back drum-type brakes - removal, dismantling and installation
14.8. See гл. 1
14.9. Disks of back brakes - check, removal and installation
14.10. Колодки a manual brake (on back disk brakes) - removal, installation and adjustment
14.11. The main cylinder of brakes - removal, dismantling and installation
14.12. A regulator of pressure of brakes - removal and installation
14.13. A hydrodrive highway - check and replacement
14.14. Prorolling of brakes
14.15. The vacuum amplifier of brakes - the general data and check
14.16. The vacuum amplifier of brakes - removal and installation
14.17. A manual brake - adjustment
14.18. The lever of a manual brake - removal and installation
14.19. Cables of a manual brake - removal and installation
14.20. The switch of a signal of braking - removal and installation
14.21. Antiblocking system (ABS) - the general data and access to codes.
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







14-4-support-tormoza-snyatie-razborka-i-ustanovka.html

14.4. A brake support - removal, dismantling and installation

Attention!
Described operations concern the brakes, the equipped both one-piston and block (two-piston) cylinders.

1. Remove колодки.
2. Turn away the hose union on a support (photo), disconnect and muffle a hose.
3. Turn away the top bolt of a support and remove a support from a disk.
4. Clear a support, observing safety rules.
5. Cautiously remove pistons the compressed air (photo), preliminary having wound the cylinder with rags.

2. 2а disk тоомоз CL25VA (rear-wheel а/м with 4-cylinder engines) 1. Copper linings 2. The cylinder 3. A cuff 4. The piston 5. A cover 6. An external lining 7. Колодки 8. Holders 9. A support 10. A finger. To grease a sliding part 11. Caps 12. Вн


2.2в the Bolt of the bottom axis


2.3 Otkidyvanie of a support for access to колодкам 1. The cylinder 2. Колодка 3. Holders


2.2б Disk brake CL25VD (all all-wheel drive а/м and all а/м with engines V6) 1. A hose 2. A cap 3. The union for prorolling 4. The cylinder 5. Cuffs 6. The piston 7. A cover 8. An external lining 9,17. Колодка 10. Holders 11. A support 12. On sites соприкасающ


2.5 Points of greasing silicone structure 1. A greasing place


2.7 Displacement of a support for installation of external linings


2.8 Greasing of holders колодок 1. A greasing place


3.5 Removal of the piston from the cylinder the compressed air


3.6 Extraction of a cuff 1. A support 2. A flute in the cylinder 3. A cuff 4. Plastic tweezers


3.2 Turn away a bolt and disconnect the union. Copper linings are subject to replacement


6. Cautiously get from the cylinder a cuff (photo).
7. Turn out the union for prorolling, get from a support fingers and covers.
8. Wash out and dry details.
9. Check up a condition of pistons and an internal surface of the cylinder. At detection of appreciable damages, deterioration of a covering of a detail replace. At corrosion detection on bolts replace bolts.
10. At assemblage grease the piston and the cylinder with a brake liquid, establish a new cuff (photo).
11. Dress on the piston a cover, having laid in a flute (photo).
12. Enter the piston into the cylinder without warps, then having pressed drown the piston against the stop in a bottom of the cylinder (photo).
13. Establish a cover on the cylinder.
14. Wrap the union for prorolling
15. Grease fingers with silicone greasing and establish with new covers in a support.
16. The further operations are carried out upside-down. Remove air from a hydrodrive of an understanding brake.

3.10 Installation of a cuff 1. A support 2. A cuff 3. A flute


3.11 Installation of a cover on the piston


4.3. A surface of a disk of a brake




«The previous page
14.3. Колодки disk (forward and back) brakes - replacement
The following page»
14.5. A brake disk - check, removal and installation