Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. The general data
14.3. Колодки disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum-type brakes - replacement колодок
14.7. The wheel cylinder of back drum-type brakes - removal, dismantling and installation
14.8. See гл. 1
14.9. Disks of back brakes - check, removal and installation
14.10. Колодки a manual brake (on back disk brakes) - removal, installation and adjustment
14.11. The main cylinder of brakes - removal, dismantling and installation
14.12. A regulator of pressure of brakes - removal and installation
14.13. A hydrodrive highway - check and replacement
14.14. Prorolling of brakes
14.15. The vacuum amplifier of brakes - the general data and check
14.16. The vacuum amplifier of brakes - removal and installation
14.17. A manual brake - adjustment
14.18. The lever of a manual brake - removal and installation
14.19. Cables of a manual brake - removal and installation
14.20. The switch of a signal of braking - removal and installation
14.21. Antiblocking system (ABS) - the general data and access to codes.
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







14-11-glavnyjj-cilindr-tormozov-snyatie-razborka-i-ustanovka.html

14.11. The main cylinder of brakes - removal, dismantling and installation

1. Disconnect the battery from weight.
2. Substitute the pallet or spread rags.
3. Release the union of tubes on the main cylinder (photo).
4. Turn away a nut of fastening of the cylinder to the vacuum amplifier.
5. Cautiously remove the cylinder from hairpins, turn on the union and muffle apertures. Get the cylinder.
6. Muffle hydrodrive tubes.

Dismantling
7. Prepare ремкомплект the main cylinder.

Attention!
In the main thing цилинцре considered cars are used ремкомплекты Nabco and Tokico which are not interchangeable. Therefore at first get necessary ремкомплект.

8. Clear the cylinder and merge a liquid.
9. Remove a cap, get a lock washer (if it is provided, the first piston and a spring (photo).
10. Get the secondary piston, having knocked with the cylinder about wooden брусок.
11. Check up a cylinder condition. At detection of scratches or the painted sites replace the cylinder

10.3 Nuts of unions on the main cylinder (it is recommended to release an alligator wrench)


10.9 Details of the main cylinder of brakes 1. A stopper 2. The filter 3. A float 4. A tank 5. The secondary piston in gathering 6. The primary piston 7. A cap 8,9 Cuffs 10. A basic washer 11. A spring 12. The cylinder 13. Уплотнители 14. At assemblage to grease with a liquid



12. Disassemble the secondary piston (primary not folding).
13. Wash out all details in spirit or a brake liquid.
14. A tank remove only if necessary.
15. Dress on the cuff piston, having tracked correctness of their orientation.
16. Dip details into a brake liquid.
17. Collect all details as their former installation, bend ears on a cap (photo) and establish on the cylinder. If the cap is damaged, replace it.
Installation
18. Before installation it is recommended to fill the cylinder with a liquid and to remove air. This measure will reduce duration of prorolling of brakes.
19. Close carving заглушками apertures under the union, fix the cylinder and fill with a liquid a cylinder tank.
20. Turn away one of заглушек, press pistons, turn заглушку and release pistons.

10.17 Before assemblage of the main cylinder bend ears on a cap


11.2а the Regulator of pressure of brakes of type And 1. The union for prorolling 2. An arm 3. A pressure regulator (неразборньй)


11.2б the Regulator of pressure of brakes of type In 1. The union for prorolling 2. A pressure regulator (not folding) 3. An arm 4. A spring


21. Repeat procedure for each of apertures on 3-4 times.
22. Instead of заглушки it is possible to close one of apertures a finger. Release a finger after pressing pistons after вытекания liquids close an aperture a finger and release pistons. After some seconds clean a finger.
Repeat procedure and execute the same actions on other aperture.
23. After the liquid will start to follow from apertures only turn заглушки.
24. Add a liquid in a tank before the top division and wrap a stopper.
25. Establish the cylinder upside-down and pump over brakes.


«The previous page
14.10. Колодки a manual brake (on back disk brakes) - removal, installation and adjustment
The following page»
14.12. A regulator of pressure of brakes - removal and installation