Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
14.1. Specifications
14.2. The general data
14.3. Колодки disk (forward and back) brakes - replacement
14.4. A brake support - removal, dismantling and installation
14.5. A brake disk - check, removal and installation
14.6. Back drum-type brakes - replacement колодок
14.7. The wheel cylinder of back drum-type brakes - removal, dismantling and installation
14.8. See гл. 1
14.9. Disks of back brakes - check, removal and installation
14.10. Колодки a manual brake (on back disk brakes) - removal, installation and adjustment
14.11. The main cylinder of brakes - removal, dismantling and installation
14.12. A regulator of pressure of brakes - removal and installation
14.13. A hydrodrive highway - check and replacement
14.14. Prorolling of brakes
14.15. The vacuum amplifier of brakes - the general data and check
14.16. The vacuum amplifier of brakes - removal and installation
14.17. A manual brake - adjustment
14.18. The lever of a manual brake - removal and installation
14.19. Cables of a manual brake - removal and installation
14.20. The switch of a signal of braking - removal and installation
14.21. Antiblocking system (ABS) - the general data and access to codes.
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







14-10-kolodki-ruchnogo-tormoza-na-zadnikh-diskovykh-tormozakh.html

14.10. Колодки a manual brake (on back disk brakes) - removal, installation and adjustment

Removal
1. Remove a disk of a back brake.
2. Remove clamping springs колодок for what press a cap and turn on 90 ° (photo).
3. Displace колодки from a board brakes (photo), remove two springs, directing and распорку.
4. Dissolve колодки in the top part and remove from a semiaxis flange, disconnect a cable of a manual brake from the lever
5. Remove a spring and a regulator, промайте details in solvent and grease a carving part консистентной with greasing.
6. If колодки vary, establish the conducted lever of a manual brake on new колодку.

9.2 Details of a manual brake of back disk brakes 1. Fingers of clamping springs 2. A board of a brake 3. A regulator 4. An adjusting spring 5. Contact surfaces 6. A basic washer 7. A spring 8. A cap of a clamping spring 9. A spring 10. Распорка 11. возвратны


9.3 Release колодки, submit on itself and remove returnable springs


Installation
7. Hook on a regulator spring for колодку and establish a regulator. Be convinced that grooves on a regulator have come into end faces колодок.
8. Slightly grease those places колодок which brakes (photo-) adjoin to a board.
9. Attach a cable to the lever on колодке.
10. Dissolve колодки and establish, having pressed to a brake board. Establish распорку.
11. Establish clamping springs колодок, fix caps, having turned them on 90 °.
12. Establish springs and directing.
13. Establish a disk on a flange of a semiaxis and fix, having screwed two nuts of a wheel. Establish the cylinder and a support.
Adjustment
14. Check up that the manual brake is completely released. Get заглушку in a board and having inserted a screw-driver, rotate a regulator for a teeth until then while колодка (photo) will not adjoin to a drum of a disk.
15. Turn away a regulator in the opposite direction on 7-8 clicks and be convinced that the disk rotates freely, without touching for колодку.
16. Put заглушку into place.

9.14 Remove заглушку and a screw-driver rotate a regulator for a teeth until then while колодка will not adjoin to a disk drum, then turn away a regulator in the opposite direction on 7-8 clicks. 1. Заглушка a regulator 2. A screw-driver 3. To take away колодку


9.7 Places of greasing on a brake board




«The previous page
14.9. Disks of back brakes - check, removal and installation
The following page»
14.11. The main cylinder of brakes - removal, dismantling and installation