Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
13.1. Specifications
13.2. The general data
13.3. The device of an automatic interlock of a nave - removal and installation
13.4. Semiaxes - removal and installation
13.5. Полуось - dismantling and assemblage
13.6. A nave and a rotary fist - смятие and installation
13.7. Nave epiploons – removal and installation, adjustment of bearings
13.8. Forward карданный a shaft - removal and installation
13.9. Epiploons of a forward reducer - replacement
13.10. A forward reducer - removal and installation
13.11. Epiploons of a distributing box - replacement
13.12. A distributing box - removal and installation
13.13. A distributing box - dismantling
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







13-7-salniki-stupicy-snyatie-i-ustanovka-regulirovka-podshipnikov.html

13.7. Nave epiploons – removal and installation, adjustment of bearings

1. Remove a nave and a fist.
2. Turn away the screw of a lock plate.
3. Turn away a counternut, fix a nave (photo).
4. Remove a plate and a special washer (photo).
5. Hook and get маслоотражатель, push out the bearing plug.
6. Remove a fist (photo).
6.б Removal of a fist from a nave
7. Get a bearing cuff
8. Выпрессуйте a ring of the internal bearing (photo)
9. Turn away bolts and remove a nave from a brake disk (Gl. 10).
10. Выпрессуйте the external bearing by means of a press, remove маслоотражатель.
11. Wash out all details.

6.3 Fixing of a nave at отворачивании nuts


5.6б Bolts of the bottom support


6.4 Nave, полуось and a  rotary fist 1. A disk of a brake 2. An epiploon And 3. The internal bearing 4. The external bearing 5. A counternut 6. A lock plate 7. Поводковая муфта 8,10 Lock ring 9. The device for manual blocking of a nave (а/м early you


6.8 Vypressovka of a ring of the internal bearing 1. Brass small beards


12. Grease a holder of the external bearing, put greasing in a nave (photo) and запрессуйте in the bearing in a nave, resting against an external ring. Fill with greasing the central space of a nave. Establish an external epiploon.
13. Establish a disk.
14. Grease and запрессуйте the internal bearing.
15. Tighten a nut of a nave with the set moment.
16. Check up freedom of rotation of a nave.
17. Grease and establish an internal epiploon

Adjustment

Attention!
For отворачивания and nut inhalings the special key (is applied by Gl. 8)

18. Tighten a nut with the set moment.
19. Release a nut and check up люфт which should be equal to zero.

6.12 Put greasing in places specified by shading


20. Turn a wheel in both directions.
21. Define a preliminary tightness in bearings. For this purpose, having hooked for the top hairpin on a dynamometer, define effort And under which the wheel will start to rotate. Further tighten a nut on 15-30 ° and establish on a nut a lock plate. Turn a wheel in both directions. Hook for the bottom hairpin on a dynamometer define effort In under which the wheel will start to rotate. The tightness is equal to difference В-А.
22. Repeat procedure and achieve a normal tightness in bearings.
23. Establish a lock ring in a nut flute.
24. Establish other details upside-down.


«The previous page
13.6. A nave and a rotary fist - смятие and installation
The following page»
13.8. Forward карданный a shaft - removal and installation