Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
12.1. Specifications
12.2. Coupling - the general data
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The dempfernyj cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydrodrive - removal
12.8. Details of the mechanism of coupling - removal, dismantling and installation
12.9. The vyzhimnoj bearing - replacement
12.10. The directing plug of a primary shaft of a check point - replacement
12.11. A kardannyj shaft, a reducer and the back bridge - the general data
12.12. Карданный
12.13. An average support - replacement
12.14. Kardannye hinges - replacement
12.15. Полуось, the back wheel bearing and an epiploon - removal and installation.
12.16. A reducer of the back bridge - removal and installation
12.17. An epiploon of a leading gear wheel of a reducer - replacement
12.18. The back bridge - removal and installation
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







12-8-detali-mekhanizma-scepleniya-snyatie-razborka-i-ustanovka.html

12.8. Details of the mechanism of coupling - removal, dismantling and installation

1. The raised noise (gnash) at inclusion of transfers or coupling proslipping testify to strong deterioration of a frictional disk.
2. Deterioration of coupling strongly depends on a manner of driving Proslipping at driving will accelerate deterioration of a frictional disk the Frictional disk it is recommended to change through each 64000 km of run.
3. For access to coupling it is necessary to remove a transmission (Gl. 7).
4. After check point removal examine coupling outside and check up a condition of fingers диафрагменной springs on a coupling casing. At detection of any damages (deformation or a bend of fingers) replace a coupling casing in gathering with a spring.
5. Gradually, in diagonal sequence release bolts, stress springs (photo) will not be removed yet. Do not damage a press plate. Fix a flywheel from проворачивания, having inserted a screw-driver into a starter aperture.
6. Turn out bolts, remove a casing of coupling, press a disk and a frictional disk. (Photo)
7. Clear of greasing and a dirt press a disk, a flywheel and the holder of the bearing.
8. Check up a condition of a surface of a press disk presence on it задиров, dents and scratches. Check up coстояние petals диафрагменной springs and палым Check up deformation of petals with the help щупа (non-uniformity of petals on height, a photo), be convinced that this size does not exceed a limit specified in Specifications. At detection of any defects coupling in gathering replace.

7.14 Before a tightening of bolts centre a frictional disk concerning a flywheel


8.4 Detachment of a spring of a spherical support of a plug of deenergizing of coupling


9. Check up deterioration of a frictional disk. Replace a disk, if distance from a surface of a frictional overlay to heads of rivets less than 0,8 mm or if on a frictional material there are any damages or oil stains.

8. 6 removal выжимного the bearing


10. Check up a condition of a surface of a flywheel. If on it there are superficial damages, прошлифуйте a flywheel. At considerable damages (breakages on a gear wreath, burning out traces on a frictional surface) a flywheel replace (Gl. 2).
11. If on coupling details oil traces establish the reason are found out and eliminate. If oil is revealed from outside a coupling casing replace an epiploon of a primary shaft of a check point.
12. It is recommended to replace the vyzhimnoj bearing. Check up deterioration of the directing plug of the bearing, if necessary replace (see more low).
13. Before assemblage apply a thin film молибденовой greasings on шлицы a primary shaft.
14. Before coupling installation centre a frictional disk concerning a flywheel with the help оправки or the suitable tool (photo).
15. Establish a coupling basket on directing pins. Wrap bolts and tighten in diagonal sequence in some stages before achievement of the set moment (photo).
16. Establish a transmission.

«The previous page
12.7. A coupling hydrodrive - removal
The following page»
12.9. The vyzhimnoj bearing - replacement