Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
12.1. Specifications
12.2. Coupling - the general data
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The dempfernyj cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydrodrive - removal
12.8. Details of the mechanism of coupling - removal, dismantling and installation
12.9. The vyzhimnoj bearing - replacement
12.10. The directing plug of a primary shaft of a check point - replacement
12.11. A kardannyj shaft, a reducer and the back bridge - the general data
12.12. Карданный
12.13. An average support - replacement
12.14. Kardannye hinges - replacement
12.15. Полуось, the back wheel bearing and an epiploon - removal and installation.
12.16. A reducer of the back bridge - removal and installation
12.17. An epiploon of a leading gear wheel of a reducer - replacement
12.18. The back bridge - removal and installation
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







12-5-rabochijj-cilindr-scepleniya-snyatie-razborka-i-ustanovka.html

12.5. The working cylinder of coupling - removal, dismantling and installation

Removal
1. Wrap a cover from a tank on a polyethylene film to prevent the big losses of a liquid at a hose detachment.
2. Release a nut of fastening of a tube of a hydrodrive to an arm.
4.5 Working cylinder is mounted on картере couplings on the right side


3. Get spring скобу and remove a hose.
4. Disconnect from the cylinder a hydrodrive hose.
5. Turn away two bolts and remove the cylinder
Dismantling
6. Remove a dustproof cover and get a pusher. Slightly knock with the cylinder on a wooden surface to take a spring and the piston (photo).

4.6 Details of the working cylinder of coupling 1. A pusher 8. A dustproof cover 3. A spring 4. A cuff of the piston 5. The piston 6. The cylinder 7. The union for prorolling


7. Turn out the union for prorolling.
8. Check up a condition of an internal surface of the cylinder. At detection задиров, scratches or the painted sites the cylinder replace.

5.1 Dempfernyj the cylinder is strengthened on a partition of a motor compartment by two screws


5.3 Details демпфирующего the cylinder 1. A cover 2. A lining 3. The cylinder 4. The union for prorolling 5. An internal surface of the cylinder 6. A spring 7. A cuff 8. The piston 9. A persistent surface демпфера 10. Rubber демпфер


4.9 Correct orientation of the piston, the cylinder and a cuff at assemblage


9. If cylinder details in a good condition, wash out their pure brake liquid and replace уплотнители (are available on sale in structure ремкомплекта). Dress on the piston a cuff, having tracked correctness its orientations (photo).
10. Before assemblage dip details into a brake liquid.
11. Collect the cylinder, having established all details in a former order.
Installation
12. Establish the cylinder upside-down. Remove air from a hydrodrive.

«The previous page
12.4. The main cylinder of coupling - removal, dismantling and installation
The following page»
12.6. The dempfernyj cylinder of coupling - removal, dismantling and installation