Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
12.1. Specifications
12.2. Coupling - the general data
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The dempfernyj cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydrodrive - removal
12.8. Details of the mechanism of coupling - removal, dismantling and installation
12.9. The vyzhimnoj bearing - replacement
12.10. The directing plug of a primary shaft of a check point - replacement
12.11. A kardannyj shaft, a reducer and the back bridge - the general data
12.12. Карданный
12.13. An average support - replacement
12.14. Kardannye hinges - replacement
12.15. Полуось, the back wheel bearing and an epiploon - removal and installation.
12.16. A reducer of the back bridge - removal and installation
12.17. An epiploon of a leading gear wheel of a reducer - replacement
12.18. The back bridge - removal and installation
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







12-17-salnik-vedushhejj-shesterni-reduktora-zamena.html

12.17. An epiploon of a leading gear wheel of a reducer - replacement

1. Merge from a reducer oil.
2. Lift a back part of the car, we will establish supports under a frame and картер a reducer.
3. Disconnect from a reducer карданный a shaft and displace aside.
4. Fix a flange of a reducer mount or the big screw-driver, having screwed bolts, and turn away a nut of a leading gear wheel.
5. Remove a flange of a reducer (photo).
6. Hook and remove an epiploon (photo).
7. Grease an epiploon and проточку in картере a reducer! консистентной greasing. Accurately, without supposing смещеия a leading gear wheel of a reducer, запрессуйте a new epiploon; so that its surface became заподлицо with картером (epiploon sponges should be turned inside).

16.5 Removal of a flange of a reducer by means of a stripper


8. Establish a reducer flange, a persistent washer and wrap a nut.
9. Having fixed a reducer flange, tighten a nut before disappearance axial люфта a leading gear wheel.
10. Turn a leading gear wheel of a reducer some times in both directions. With the help динамометрического a key with a scale in some Н.м. Also measure twisting moment size at which leading gear wheel it starts to be turned. This moment is equal anticipate-telnomu to a tightness in bearings of a leading gear wheel and should correspond specified in Specifications. If the moment appears less demanded tighten a reducer nut until then the necessary moment will not be reached yet.

16.6 Extraction of an epiploon of a reducer


Attention!
The preliminary tightness is provided распорной with the plug of bearings of a leading gear wheel. If size of a preliminary tightness more recommended the plug will be deformed. In this case a reducer it is necessary to remove and replace распорную the plug.

17.8 Back bridge (arrows specify assorted connections at bridge removal)


11. Further assemblage is carried out upside-down.
12. Upon termination of fill in in a reducer oil.

«The previous page
12.16. A reducer of the back bridge - removal and installation
The following page»
12.18. The back bridge - removal and installation