12-15-poluos-zadnijj-kolesnyjj-podshipnik-i-salnik-snyatie-i-ustanovka.html
12.15. Полуось, the back wheel bearing and an epiploon - removal and installation.Removal
1. Lift a back part of the car.
2. Remove wheels.
3. Remove a brake drum (Гл.10)
4. Disconnect a cable of a lay brake and a hydrodrive highway (Гл.10)
5. Turn away a nut of a board of a brake.
6. Remove полуось in gathering with a brake (photo). If by hand to get полуось it is not possible, it is necessary to take advantage of a shock stripper with an adapter which is established on hairpins of fastening of a wheel.
7. Hook and get an external epiploon (photo). An epiploon it is necessary to change each time at semiaxis removal. A new epiploon запрессуйте оправкой suitable diameter.
8. Press the bearing from a semiaxis. This operation is recommended to be carried out in car-care centre as the stripper or a press is necessary. If these приспосоления are available, execute the following.
|
14.6б Removal of a back semiaxis by means of a shock stripper
|
|
14.9 Raskontrite a nut of the bearing of a back wheel for what unbend a washer teeth
|
9. Unbend a teeth of a lock washer of a nut of the bearing (photo).
10. Turn away a bearing nut воротковым a key (photo) for what clamp полуось in a vice through the soft prorate.
11. By means of a press or a stripper remove полуось from the bearing and a brake board.
12. Beat out an epiploon from обечайки the bearing (the epiploon is subject to replacement).
13. If on an external holder of the bearing there are damages the bearing replace. For this purpose beat out a holder from обечайки by means of brass a small beard (photo).
|
14.13 Removal of an external holder of the bearing
|
|
14.7 Extraction of an epiploon
|
|
14.10 Otvorachivanie of a nut of the bearing of a back wheel
|
Installation
14. Оправкой suitable diameter запрессуйте in обечайку a new epiploon of the bearing. Grease working edges of an epiploon консистентной with greasing.
15. Cautiously запрессуйте an external holder of the bearing hammer blows on brass оправке.
16. Establish on полуось the dividing plug so, ' that the facet on an aperture has been turned towards a flange semiaxes (photo).
17. By means of brass оправки it is cautious запрессуйте the bearing.
18. Establish ring and lock washers, it is correct сориентируйте and wrap a bearing nut.
19. Законтрите a nut, having bent a teeth of a lock washer.
|
14.16 Orientation of the dividing plug of the bearing at installation on полуось 1. A flange of a semiaxis 2. The plug
|
|
14.22 Adjusting linings are established between an end face of a beam of the back bridge and the case of the bearing and provide necessary longitudinal люфт semiaxes
|
20. Put консистентную greasing on the bearing and in проточку at an end face of a beam of the back bridge.
21. Grease шлицы semiaxes трансмиссионным with oil, put консистентную greasing on working edges of an epiploon.
22. Establish all removed adjusting linings (photo).
23. If both semiaxes acted in film, establish one of them. Measure longitudinal люфт semiaxes (photo) which should be 0,3-0,9 mm. If люфт does not correspond to norm adjust for what remove полуось and add or remove adjusting linings (the thickness of linings is specified Specifications).
24. Establish the second полуось (if acted in film) and adjust люфт selection of linings.
25. Further assemblage is carried out upside-down.
|
15.5 Otvorachivanie of bolts of a reducer of the back bridge
|
|
14. 23 check longitudinal люфта semiaxes
|
|