> Average support - replacement. Nissan Terrano II (with 1985 on 1999 of release)
Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
12. Coupling карданный a shaft and the back bridge
12.1. Specifications
12.2. Coupling - the general data
12.3. A coupling pedal - removal, installation and adjustment
12.4. The main cylinder of coupling - removal, dismantling and installation
12.5. The working cylinder of coupling - removal, dismantling and installation
12.6. The dempfernyj cylinder of coupling - removal, dismantling and installation
12.7. A coupling hydrodrive - removal
12.8. Details of the mechanism of coupling - removal, dismantling and installation
12.9. The vyzhimnoj bearing - replacement
12.10. The directing plug of a primary shaft of a check point - replacement
12.11. A kardannyj shaft, a reducer and the back bridge - the general data
12.12. Карданный
12.13. An average support - replacement
12.14. Kardannye hinges - replacement
12.15. Полуось, the back wheel bearing and an epiploon - removal and installation.
12.16. A reducer of the back bridge - removal and installation
12.17. An epiploon of a leading gear wheel of a reducer - replacement
12.18. The back bridge - removal and installation
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







12-13-srednyaya-opora-zamena.html

12.13. An average support - replacement

1. Turn on two nuts of an arm of a support, remove both half of arm.
2. Designate a relative positioning of flanges of forward and back sections карданного a shaft (photo).

11.2 Before a detachment карданного a shaft designate mutual position of flanges


12.2 Designation of a relative positioning of flanges of sections of a shaft


12.3 Fix карданный a shaft and turn away bolts of flanges of forward and back sections


12.5а a flange Nut законтрена wreath cave-in in a groove of a carving part of a shaft


3. Fix карданный a shaft and turn away bolts of flanges of forward and back sections (photo).
4. Designate position of a flange concerning a groove on a carving part of a shaft.
5. Turn away a flange nut карданного the hinge for what correct раскерненнуго a part of a wreath nuts (photo), screw in a flange bolts and fix section of a shaft from проворачивания (photo). 6. Remove a flange (photo).
7. Remove an average support by means of a hydraulic press (выпрессовать an average support and запрессовать new it is recommended in car-care centre).
8. At запрессовывании an average support, be convinced that the letter "Р is turned to a forward part of the car.
9. Apply a thin film консистентной greasings on an end face of an average support and a washer. Establish a washer into place.
10. Combine a label of a flange with a groove. Establish a flange.
11. Wrap a counternut and tighten with the set moment, then законтрите, having pressed a nut wreath into a groove of a carving part of a shaft (photo).
12. Combine labels on flanges and wrap bolts.
13. The further operations on assemblage are carried out upside-down. At installation of an arm of an average support keep in mind that the joint in a rubber pillow of the bearing of a support should be turned upwards.

12.11 Two types of nuts of a flange of an average support – with a fillet (at the left), a standard nut with a washer (on the right)


12.5б Otvorachivanie of a nut of a flange


12.6 Removal of a flange of an average support with forward карданного a shaft



«The previous page
12.12. Карданный
The following page»
12.14. Kardannye hinges - replacement