Nissan Terrano 2 with 1985 on 1999
1. The maintenance instruction and to maintenance service
2. Car maintenance service
3. Четырехцилиндровыв engines
4. Engines VS
5. All engines
6. Systems of cooling, heating, ventilation and air-conditioning
7. Fuel and exhaust systems
8. System of an electric equipment of the engine
9. System of decrease in toxicity of exhaust gases
10. A mechanical transmission
11. Automatic transmissions
11.1. Specifications
11.2. The general data
11.3. Draught of management of transmission - adjustment
11.4. The blocking switch - check and adjustment
11.5. Kick-down - the switch - adjustment
11.6. A rod of a vacuum diaphragm - adjustment
11.7. A back epiploon - replacement
11.8. Automatic transmission - removal and installation
12. Coupling карданный a shaft and the back bridge
13. A running gear of cars with the wheel formula 4x4
14. Brake system
15. Suspension brackets and a steering
16. A body and furnish elements
17. Electric equipment system
 







11-3-tyaga-upravleniya-transmissiejj-regulirovka.html

11.3. Draught of management of transmission - adjustment

Cars with the floor selector
1. Translate the selector from position Р in "1", clamp operation in all intermediate positions thus should be felt. If operation is not felt, or the index does not coincide with designations draught is necessary for adjusting.
2. Translate the selector in River position
3. Release counternuts (photo).
Rear-wheel cars
4. Tighten a counternut of X (photo) against the stop in a selector arm, pressing the lever in a direction of position R (the button not to press).
5. Turn away a counternut X on 1/2-1/4 turns and tighten with the set moment.
All-wheel drive cars since 1987
6. Pressing the lever in a direction of position R (the button not to press), tighten a screw coupler until then while the coupler will not be combined with a vein of a cable (photo).
7. Turn away a coupler on 1 turn and tighten counternuts with the set moment.

2.11 Counternuts of draught of automatic transmission on cars of 1987-88 with the selector on a steering column


2.5 Adjustment of draught in cars with the floor selector (all-wheel drive а/м 1988 and all rear-wheel а/м since 1987) 1. Sector "Р"        2. A counternut X 3. Counternut Y 4. Not to press


2.6 Adjustment of draught of transmission on all-wheel drive cars (with 1987).


8. Translate the selector from position Р in "1" and be convinced of smoothness of a course of the selector.
Cars with the selector on a steering column
9. Translate the selector from position Р in "1", clamp operation in all intermediate positions thus should be felt. If operation is not felt, or the index does not coincide with designations of sectors draught is necessary for adjusting.

2.12 Adjustment of draught of transmission on cars of 1987-88 with the selector on a steering column 1. A counternut And       2. An item plate 3. A counternut In  4. Not to press


3.3 Check of a chain between gauge conclusions in various positions of the selector 1. The diagramme of the closed conclusions in various positions of the selector


3.5б the Typical arrangement болтав the blocking switch (are shown for all-wheel drive cars 1987 - 88)


10. Translate the selector in River position
11. Release counternuts (photo).
12. Tighten a counternut And (photo) against the stop in an arm, pressing the lever in a direction of position R (the button not to press).
13. Turn away a counternut And on 2 turns and tighten a nut In with the set moment.
14. Translate the selector from position Р in "1" and be convinced of smoothness of a course of the selector


«The previous page
11.2. The general data
The following page»
11.4. The blocking switch - check and adjustment